Hello everyone,
I want to evaluate the power consumption in idle mode of the nrf9151 sip.
Environement:
nrf9151dk_rf9151_ns
nRF Connect SDK Toolchain v3.0.2
VScode...
I’m using SMP over UART to send the erase command ( {"slot": 1} ), and it only erases the application core image (image 0). I also have a network core image (image 1) present...
So i am currently referring this ticket and from that I get to know that when when setting parameters for create config (HCI_LE_CS_Create_Config) command for channel sounding...
I am trying to get the lowest possible power consumption for my Thread device, so I am experimenting with different configurations.
Currently I'm testing with SSED ( Synchronized...
Hi Noridc expert ,
I am trying to configure using nsib + mcuboot on nrf52840,
I need to build the image with only public key avaliable , and sign the image else where...
Currently the Matter code generation process is a bit confusing to me. Part of the code needs to be generated before building, using west zap-generate. Another part of the...
Hi,
We wanted to create a device what control with a remote controller but we want to controll this device by smartphone also.
We going to use 51822 but it is not exactly...
Hello.
Our company develop BLE device and make some applications(android/iOS) for updating ble devices.
Those applications use nordic DFU source for installing firmware...
Hi
I want to configure SAADC channel to work in oversampling mode, and to enable burst mode.
nRF52832 Objective Product Specification v0.6.2 says:
"CH[n].CONFIG.BURST...
Hi,
I'm looking to use the nRF51822 in a new design and would like to know if there is tool available to calculate how long it will be able to run of a battery when set to...
I can discover 6 services by Master Control Panel over Android device, but only 4 services on ios 9 device, I can't discover Gap and Gatt service. What's more, when i try...
Hi all,
we are using NRF24L01+ ic for our application .we want to have TAG transmitting and receiving end separated so we are using the two NRF ic .We want that there should...
Hi,
Does Nordic provide a version of nRF Toolbox or similar to run under Windows 8.1 (not Phone)?
If not, can anyone recommend any free general-purpose tools or utilities...
I encounter a problem to switch to DFU mode from UART when BLE is connected and one 5ms timer keeps running for heart rate sensing alg. Maybe it's the reason keeps BLE busy...
Hi,
I want to use BLE to run DFU. My sdk is 8.1.1 and base project is ble_app_uart. When I use nrfgo Studio to program softdevice, bootloader and app, It can't enter app...
I am seeing excessive current in System ON, Idle mode. I am using WFI(). I have verified that
operation is being held at that instruction by using GPIO pin. Idle mode is...
Our manufacturer received new nRF51822QFAAH0 parts. Previously, we were supplied nRF51822QFG2 parts.
According to your PCN_092-1.2 Final.pdf document, there has been a...
Hi,
I can start MCP without the dongle PCA10031 (which I have updated the firmware on) and it starts ok, but when I then plug in and select the device COM 5 - 6xxxxxxxxx...
I would like to ask how to make advertisements which are less than one second. In my application, i need to scan for devices, when i find my specific device, i start to advertise...
I'm trying to programmate a simple blinkind led project to a custom board with a nRF51822 I did. I'm using a stm32 discovery to connect the custom board throw the SWD port...
I'm trying to update my beacon to use 8.0.0 SoftDevice 110. I've downloaded the 8.0.0 precompiled softdevice hex and loaded the Keil dfu_dual_bank_ble_s110_pca10028 project...
