Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I read timer example of SDK7.0/6.0, and found that often we write some code to tigger the clock.
but the same example of SDK9.0 needn't. why ?
the code of SDK7.0: NRF_CLOCK...
Hi,
I am developing ble apps with the BL600.
I am coding a source file with the keil IDE. And this source is deployed to the nRF51 DK board through the nRFgo Studio....
hello,
i am unable to update application or softdevice or bootloader via master control panel 3.9.0
while doing so, it shows error:"FAILED TO OPEN TRANPORT BACKEND". ...
I followed the Nordic Tutorial located here . I'm using a PCA100028 Dev Board, MCP 3.9.0.6, and a Segger J-Link Plus. I'm using Keil uVision5, and used the pack installer...
I have a set of characteristics on my ble peripheral (nrf51) which I display with nordic control panel tool (android). but when I deleted one characteristic on the peripheral...
Hi, I am evaluating the use of Gazell and BLE as a possible solution for my project. I had heard that there was a way to have both BLE and Gazell running on a device at the...
we will do some measurments and answer when we get some time to spare for this. Others are welcome to answer/comment freely about their experiences/knowledge.
I have some custom hardware (nRF51822) with a couple sensors on it and would like to have the data sent via BLE to a smartphone. This may be timer based on triggered by an...
Hi :
I want to update the firmware of 24le1 over the air ,follow the 3 step ,fail.
download "rf_adapter_nRF24LU1P.hex " to the nRF24LU1 by nrf6310,and connect to PC...
I am using the nrf52832 to communicate uart with hw flow control and a baudrate of 9600 and fifo.
Everything is going well most of the time, but sometimes the other device...
I write an infrared receive driver on example ble_app_uart with softDevice 6, but it not work after I use softDevice 8.How to fix it ? Is there an offical infrared receive...
I'm trying to generate a 1kHz PWL and call a function every 1ms the code is below.
My initial though was to set TASKS_CLEAR once the timer reached the max pwl value.
Oddly...
Hello,
I am using multilink central example to connect to multiple peripherals. But I am facing a problem in connecting 2nd device.
After connecting the 1 st device, upon...
Hi,
the S130 supports multiple connections for the Central role. Is it possible to connect to multiple devices at the same time? E.g. calling sd_ble_gap_connect() asynchronously...
