Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi Nordic guys,
we are developing a peripheral device with a custom protocol to exchange data.
we are using nrf51822 with SDK 6.0 and SoftDevice 7.1.0 (s110 being peripheral...
I can not find information about layer stack-up and whether the via-in-pads were filled, please provide this information. We are thinking about a variant with thin outer layers...
Hi, I am trying to combine SPI, microESB and BLE. BLE and microESB will not be combined in realtime, but rather be two distinct modes, and not run at the same time, and therefore...
[test result] change to use Timer1 of timer example,it failed. if you use timer0, it is OK..
SDK IS 9.0:
nRF51_SDK_9.0.0_2e23562\examples\peripheral\timer
[test step...
Is there a way to access the lower level clock which a connected slave uses to stay in sync with the master. We want to use this to keep our PWM in sync. We are looking for...
Hello,
After looking into forum regarding usage of S130 stack for using the device as both central and peripheral, I understood that the peripheral and central can concurrently...
Hi All,
I have query regarding PWM usage in nRF51-DK. I have a requirement to control 3 LEDs (brightness and power) simulatneously. I intend to use PWM for the same. But...
Hi there! An error occurred in device manger. It was caught at the first APP_ERROR_CHECK in device_manager_evt_handler. Error code is 0x88. I can't find this error code in...
Hello,
I do not see the bootloader files for this example in SDK 0.9.2. Where can I find the boot sequence for the ble_app_hrs example, and in what files is the boot setup...
Hi,
I don't see in SDK 0.9.x any examples pertaining to accelerometer peripherals. I see a TWI sensor example from the nRF51, but I am working with the nRF52. Are there...
The nrf8001 datasheet seems to mention that there should be no connections when sleep command is sent. So I wanted to call aci_disconnect first. But what reason do I use?...
Hello,
I received the nRF52 DK and tried setting it up as described in infocenter-->nRF52 Series --> Get Started.
I have the following installed:
Keil uVision5
Error...
Hi,
I noticed that I'd occasionally hit an error when calling into nrf_drv_spi_transfer using the SPIM driver (SPI0_USE_EASY_DMA set). nrf_drv_spi_transfer was returning...
