I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I received my nRF51 DK (with nRF51422, PCA 10028) and I could successfully run the S130 demo app thats included with SDK 8.0.0.
The above demo demonstrates for e.g. :
...
I was upset early this afternoon because I was experiencing issues with buttonless DFU on Android. As is usually the case, I assumed it was my fault.
First, I reverted...
Hi Nordic--
Our custom nRF51822 design has 13 signals routed into the app_buttons module through the GPIO -> GPIOTE->PORT -> nrf_drv_gpiote.c -> app_buttons.c path. For...
Hi,
I have a problem to program an external board with my PCA10028 board. My external board is a Xuntong chip.
( Heart-Rate-Monitor-2-4GHz-SOC-BLE-Module-based-on-nRF51822...
I'm trying to measure absolute minimum power consumption of the chip using the PCA10028. I cut SB 9, and applied a very sensitive current measuring device to P22. I'm running...
Hi all,
I am having ADXL335 Acellarometer board. Here its giving data of X,Y and Z axis directly in analog form.
So how should i configure my IO pins of PCA10001 board...
I've been reading about minimizing the amount of time that the SoftDevice blocks the CPU for, but most of the answers have to do with old revs of the chip and old versions...
We have a peripheral device that we would like to have sleeping 99% of the time. I have a single timer waking it at 1-second intervals to look for things it might need to...
Hi,
I am trying to get date and time on my nrf51822 but struggling a bit. I would like the nrf to receive the time over BLE and then increment it internally using the RTC...
I have a system using the Gazell link layer in which 2 devices stream data to a single host. Each of the devices is assigned a different pipe, and all three (host, and both...
I have successfully set up UART/Serial Port Emulation over BLE example. I have modified it so that it works with two nRF51 DKs, one acting as a central and other acting as...
Hello,
I would like to know whether the below PA can be interfaced with nRF51822?
For our application we need to increase the power of the BT. so I have selected the below...
Hi,
From other forum posts it seems to be very important to follow the reference layouts when designing nrf52 PCBs, but I can only find the reference files in Altium format...
Hi,
I have a nrf51 dongle and I try to connect my Android smartphone to it. My smartphone is BLE compatible, so no problems here.
I flash the firmware using master control...
