Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi
I got a new chip, marked as "QFAABA / 1542AB".
I see that both errata versions 1.1 & 1.2 seem to be relevant.
Can you tell me which errata should I refer to?
Thanks...
Hi Nordic,
I am adding pstorage capability to ble_app_proximity example. Before adding pstorage, the example could receive Immediate Alert from a central and set on/off to...
Hi i'm a newbie in nordic chip. Can someone please explain to me that how to enable and configure the timer interrupt and what kind of setup need to be done?
Example in...
There is a mistake in LEDS_INV_MASK definition:
PCA20006.h / nRF examples 10.0.0
#define LEDS_INV_MASK 0x11111111
// blue will be erratic
PCA20006.h / nRF examples...
Hi,
when i setting up a new project in uVision, i get a crazy Error wich i cant handle with.
My error is --> main.c: error: C3906U: Malformed via file '.\main.__i'....
Hello,
in the new version of sdk (11.0.0) you support s130 only.
That means the code contains both peripheral and central implementation.
Does it mean that s130 consume...
The following seems to suggest each write event can only contain 1 byte of data at a time.
/**@brief Event structure for @ref BLE_GATTS_EVT_WRITE. */
typedef struct...
Been playing with NRF24L01+ for a while and mostly they work as I expect. Now, I'm trying to use an ACK payload, but whenever I try to set up the receiver to put a payload...
Hi, I'm using trying to use the DFU via BLE, dual bank example from SDK 8.1.1 (with SD 8.0.0) and got it all working up to the point where I call "activate image and reset...
Hi,
I have a problem that the ANCS keeps resetting my board, so I was able to reproduce the problem on the PCA 10028 dev board.
Conditions:
iOS 8.x or 9.x
No...
Hello,
I am running Windows 10, nRFgo Studio 1.21.1 and Keil uvision 5.16a.
I was doing some tests with my nRF51 DK board, like loading the beacon example found in the...
Hello,
I am using simple_adc__pca10028 from 8.0.0 SDK to read values from my sensor, its a kind of tensometer. My configurations are:
NRF_ADC_CONFIG_RES_10BIT...
Dear sir,
I am using your NRF24L01+ chipset with STM32F407ZET6 controller for 2.4GHZ RFID communication. can u please share the STACK for this controller.
