I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I am programming nRF51 on Keil. My app uses BLE with softdevice S130, PWM, and I2C communication with two sensors. Also RTT for debugging.
I have already reached...
Hi there!
I use RedBearLabs Nano (nRF51822) for at setup where I've developed BLE code in Arduino to communicate with apps on both iOS and Android.
Now I need to ensure...
Hello,
We recently received an eval kit the the nRF52832, but we were told not to take current measurements with this version. This presents a problem since we are evaluating...
I am using this mbed workthrough, to create a custom GATT Service in C++. However, this code only creates characteristics with UUIDs:
uint16_t percentageUUID = 0xA002;...
This thread mentions having the master read the DFU Revision Characteristic to determine the DFU revision. I've based my DFU and application off the dfu_dual_bank_ble_310_pca10028...
Could you estimate the free space for Application on nRF51 and mRF52, on this case for Homekit with FOTA :
Boot Loadeer with FOTA
Homekit Enable
BLE Software Device...
What are the options to update firmware (Application/Bootloader/Softdevices) for multiple devices built on NRF51x22 ?
Using Master Control Panel could take days programming...
Dear Nordic Team,
I am using HID mouse example code in my nordic dk board.
I can able implemented fallowing logic in my code to do left , right and middle button click...
Hi,
I am using nRF51422 with SDK 9.0 and SoftDevice130 with nus service. I have a custom android app running on BLE uart service. Data communication and connection handling...
How to save the uart app on my nrf51dk board? it only runs when i connect it with the usb. another question nrf51dk have a nrf51822 chip(SoC)?
please help me out. i want...
Hi,
I have installed EmBlocks 3.2 (the last one) but only extremely simple examples will compile.
It appears that the support files in wizard/arm/nordic/nordic.zip/Common...
I have been struggling with the custom characteristic implementation. I have followed the great tutorial on custom service that is online but there is really no doc or information...
The nRF Beacons iPhone or Android app requires adding a new beacon devices in order to notified events. Is it a must for beacons? Or is it just a one step for examples. In...
I try to advertise with a custom UUID and I do not know how to do it.
The standard services works with 16 bits and I need to work with 128 bits
So how can I do it?
Thanks...
Dear Nordic family,
I am using Bluetooth Low Energy, Beacon module with ARM Core from Tindie ( Product link ). The reference manual from their website is attached IMM-NRF51822_RefMan...
