In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
I'm trying to implement bonding. I first initialize pstorage, as a separate call from main. Then I call...
Hello Everyone
i have J link for ARM processor from IAR 2008 module version 6 which specify support for swd, As I checked it on IAR website it support CORTEX-M0 processor...
I use pin SDIN, SCLK, CS, DC.
but how do I connect the pin nrf51822
spi_master_example is
#define SPIM0_SCK_PIN 25u /**< SPI clock GPIO pin number. */
#define SPIM0_MOSI_PIN...
I have been reading about code regions in the nrf reference manual and understood about CLENR0 and how to use it. I have however, two questions
What is Pre Programmed...
I am using the SPI Slave port in the nRF51822 and am always transferring 20 bytes. No matter what I do, it seems that the status register in the IRQ says that I got a TX buffer...
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hi,
I need to be able to communicate between two boards via UART. I had a look at the example from Ole provided here: devzone.nordicsemi.com/.../ as well as other references...
Hello,
I am wondering if I can use any 128 bit UUID value.
For example, in the example uart project, Nordic UART Service = 6E400001-B5A3-F393-E0A9-E50E24DCCA9E is used...
If I want to stream samples up to the nRF Toolbox HRM iOS app plot, what is the fastest that I can call ble_hrs_heart_rate_measurement_send in firmware assuming I have nothing...
Hi,
I'm using nRF51822 Development Kit and trying to program softdevice with nRFgo Studio. The file to program is C:/Program Files (x86)/Nordic Semiconductor/nRFgo Studio...
I'm using S110 version 7.1.0, but need a way to validate in general which S110 and which SDK version I have associated with this .uvprojx project.
Much of this stems from...
I'm running the ble_app_beacon_s110_pca10028 example on my NRF51 dongle. The good news is that I see a beacon transmission on my iPhone 6 on this "Pally BLE Scanner" app....
We are developing a new BLE tag product using the nRF51822. We would like to assemble the PCB and battery in a single operation then program the product sometime later. Can...
