Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hi,
I'm getting the following error over and over again from the nrf connect plugin in VSCode:
[west]: FATAL ERROR: failed manifest import in bsim (tools/bsim): [west...
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the nRF Connect...
I'm writing an application for the nRF54L15 that periodically receives the local time via bluetooth and keeps track of time on its own between syncs. I'm using a 10ppm external...
My product currently has DFU (Device Firmware Update) functionality enabled, but I want to allow firmware updates only after receiving a specific command via BLE. This is...
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
In Electrical specification Table 1 (current consumption in forced High Power mode) lists a typical value of 7.2 mA , just want to confirmed this is correct and not a typo...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
I have a single-ended signal that spans [0V,3.3V] and is centered around V_bias=1.65V (=3.3V/2).
I want to use the NRF54L internal gain to amplify only the AC parts of the...
this my yaml.file to use partition manager, beacause iam implementing DFU, USB MSC with fatfs in single project
fatfs_storage :
address : 0x00000000
size : 0x00200000...
Hi, I am using custom nrf52840 board with sysbuild, MCUboot+firmware loader, static partitioning, settings storage (OpenThread) and littleFS storage and I cannot get the thing...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Im trying to use the https://github.com/apache/mynewt-mcumgr-cli project to update my rfF54L15 with a DFU package
Setup: Raspberry PI 4 and and nrF52840 USB Dongle
I...
Help me please!!!
nRF52840 DK stops to scan after 3 hours working.
Project is based on central_nordic_uart_service.
Scan params
it works fine 3 hours and then BLE...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
