Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hello everybody,
I am currently experimenting with BLE on the nRF51-Ek. At measurement on the oscilloscope, the BLE protocol shows a behavior that I do not quite understand...
Hello.
I get error 0x10 (error for invalid flags) when i want to write to peripheral with my master module. I use the same code i always used, and i didnt change anything...
Hello.
I written code for nRF51822 w/ MPU6050 in S110(8.0.0) and Keil.
I tried to setup gyro as bellow.
twi_master_init(); => mpu6050_init(MOTION_SENSOR_ADDRESS);...
Hello
I have connected the nrF51-DK board and it was recognized by the computer.
I have managed to put in in a boot loader mode.
Since I switched it to boot loader...
I have three pca10001 boards. One is programmed as multilink central and other is programmed as multilink peripheral. when both peripherals are connected to central, the central...
I'm a newbie for Nordic development.
I just noticed that softdevice, app, and bootloader share the same CPU, RAM and Flash at the same time. This three software modules...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
Hi
I use an avr attiny441 with the nRF24AP2. Communication is over SPI byte flow. After start up, I get the start-up-message from nRF24AP2. That's fine. Afterwards, when...
Hi
the PWM frequency should reach 8MHz( duty cycle is 0.5 )when use timer0(16M) without SD.but i revised timer demo code from peripheral and only get 50KHz.i don't know...
Hi everyone,
I've found a few posts and a lot of info but I'd like to know if there is an existing example that merges a few of the examples found here ( github.com/.....
Hello.
I want to retain the value of a certain variable after issuing a system reset (sd_nvic_SystemReset).
Can this be done without storing it in the flash memory?
...
Hello.
I use SDK 8.0.0 and PCA10028 board. I try connect board to the Windows 8.1 PC ( i have Tablet PC and Desktop PC with BLE dongle). For connect board to Windows i...
I think I understand what these two flags do, the SYS one returns the system attributes, which I assume means data representing the CCCD for the service changed characteristic...
Hello,
Is there any compatible arduino lcd with existing library for the nRF51 Chipset?
So I can just plug it on the nRF51-DK, include the library and "lcd_wirte("text...
