Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi, Nordic Engineer:
Would you like to give me some advice? On my hand, i have a slave ble device(not nrf51822, also i can not change the code). I want to run s120 softdevice...
i am able get the status of led of pca10001 board using usb dongle. now i have to make other pca10001 board as central and want the same data of it? Kindly help, i shall b...
We are planning to optimize the radio-frequency signal,so the some docunments like Simulation model are needed.which can help optimize the RF signal through ADS simulation...
In ble_advertising.c, line 165, you can see such interesting code. I assume it is a copy/paste error:
if(p_advdata->p_tx_power_level != NULL)
{
m_advdata.p_tx_power_level...
For the first, impressed by your intoducing NRF52 chip.
Question: what`s NRF52 indoor range using onboard antenna and maximum output power (+4dBm)?
Thanks.
Hi~
I am struggling to get the BLE packets detected by nrf sniffer (v1.0.1) using wire shark. Its only showing "ADV_IND[Malformed Packet]" periodically. I didn't understand...
I believe what I am asking is extremely specific, but keeping hope that I might get some direction
I have used a clone ST- Link v2 programmer to download code into a NRF51822...
Hi all,
I would like to trigger some actions on difference devices communicating with the ANT protocol based on the distance they are from each other. A simple example...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi all,
First of all thanks for Nordic team for the excellent support. It is very useful for a beginner like me to get started on BLE development.
I am using the nRF51422...
The issue is that if a peripheral needs to enable interrupts (or anything else partly protected by the SoftDevice) and is configured before enabling the SoftDevice, the NVIC_...
Hi, I use nRF24LE1 configured for power down on register retention mode with RFRx active.
When the CPU is on power down i don't have any interrupt from RFIRQ.
Init configuration...
I downloaded the power consumption example code to a nRF51-DK to measure the current consumption during SYSTEM ON and SYSTEM OFF state.
For the SYSTEM ON state, I used...
On our custom board, we have a dedicated hardware reset IC which toggles the nRF51822's nRST line low in response to a magic button press. The nRST line has an external 100k...
