Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I am getting the following errors.
Building ‘1’ from solution ‘1’ in configuration ‘Debug’ Generating linker script ‘1.ld’ Linking 1.elf Output/1 Debug/Obj/ses_nRF_Startup...
Hi,
On STM32 and some other platforms I'm able to get an address that I can write to in order to set the value of a single pin. While (like on nRF) there is one output register...
Hi,
we are looking for a software developer (freelancer) for a Bluetooth LE (BLE) project on a BL652 module. Is there a available developer arround munich / germany.
thanks...
Hello,
Migrating from 1.0.0 to 1.0.1 I've noticed that softdevices in external/softdevice are zipped except SD 132 3.1.0. Does Mesh 1.0.1 break compatibility with SD 132...
Hello,
I do a big scatternet of nRF52840 and i want to deploy code update from a single point. Is there any way to do DFU between 2 nRF52 ? Can a nRF52 propagate it's own...
I am trying the buttonless DFU example from SDK14.2.0. I am not following the testing procedure mentioned at infocentre for SDK14.2.
Followed test procedure:
1. Erase...
I've been using the nrf_twi_mngr_perform() function assuming that my transaction was complete when the function returned. Because of this, I felt safe keeping my descriptors...
Hi Sir/ Miss:
I've a custom peripheral heart rate device.
I use central example "ble_app_hrs_c" to connect it by PCA10040.
After I set up the service (Target_UUID) and...
Dears,
I'd like to add service while connection.
Now I am using UART service and want to add HID service when I put button.
How to add HID service while connection...
I am using Master Control Panel for doing DFU on nRF52832 DK. The nRF52832 is having example dfu code dfu_test_softdevice_w_bootloader_b_s132.hex from sdk11.
nRF51 dongle...
Dear experts,
I'm a new user of NRF52 technology and I use:
Keil µVision v5
NRF52832 (PCA10040)
Keil software pack 8.15 from Nordic Semi
debugger Cyclone...
Hi Nordic
I am porting an application from the EM9304 SoC to the nRF52810.
In the old application it was possible to send 26 bytes of manufacturer specific data (plus...
Hi,
I use BMD-350 on NRF52832 with SDK v13.0.0
I configure my radio to run the BLE at -20dBm power through the API sd_ble_gap_tx_power_set()
But few seconds after starting...
Hi!
I once set up a simple project using SDK 12 and the HRS example.
Now I tried porting it to SDK 14 and SD 5. That didn't work out well.
So I started things from...
Hello everyone,
I am working with TWI and broadcasting of data using ble_app_beacon. I am facing a problem in broadcasting of the data. I have complied the code and it runs...
