Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
What are the general causes of SDS assert in nrf51/52 ? Assuming that SW has been tested, is there something that could happen in the code that would cause the assertion...
Hi All,
I'm using "scanForPeripheralsWithServices" of iOS to the BLE devices.
"scanForPeripheralsWithServices" sometimes never return anything.
I have to stop scan or...
Hello! I'm trying to build a program for nrf51822 via QT Creator.
I'm using QBS for build. I have a makefile from SDK examples for nrf51822. Someone can help me, how to setup...
Hi all,
I have the exact issue mentioned here - github.com/.../9
I have updated my makefile to generate only one bin file from the Softdevice Hex file, but still I'm getting...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi,
I'm testing the ble_app_beacon on my nrf51422 dk. I followed the instruction in the sdk documentation . All was well. Then, I tried to test with the nrf Beacon app...
Hi,
I need to measure the current consumption for nrf51DK using an Oscilloscope. I have read the user guide and they have mentioned some connectors for it. Is it possible...
I'm just using the s110 double bank example and I have gotten it to run on the dev board just fine.
When I try running it on a custom board with a NRF51822 version 3 that...
I'm having some weird issues with using pstorage and the softdevice s110 8.0
I'm saving around 600 bytes of data using pstorage. All seems to be working on the nrf51 DK development...
I'm working based on the HRS central application, and have run into an issue where my if statement is entered even though the condition is not met. In this case, the nrf attempts...
I'm currently using the pstorage functions to be able to store permenant data when turning off the power, it works good with me while writing or reading but when I turn off...
I'm trying to implement ANT+ style frequency hopping, where it would change channel whenever it detects a raise in packet loss. For that I need to be able to switch channel...
Hi,
I 'm using MCP v3.9.0.6, softdevice v7.2.0 and pca10003 board.
After load bootloader program to board. I use MCP to load application for it. In MCP, I choose device...
HI People,
I use nrf51822 CEAAE00 (0x0079) chip which has 256 kB FLASH, 16kB RAM. I faced a problem when compiling the bootloader for it. The solution was I am using a...
I am trying to build a custom board, based loosely on the nrf51-DK (which I have been testing). I haven't ever directly programmed a chip before (always used interface MCUs...
