hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I am trying to set up an environment based on CMSIS Packs. However, when using some components from nRF_Libraries, these lines get added to RTE_Components.h:
#define GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Softdevice Version: 8.0.0
SDK: 9.0.0 IC:
NRF51822 Rev 3
service: NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am working on nrf51 iot sdk. I have created a IPv6 tunnel in HE and is able to ping the gateway as follows:
root@raspberrypi:/home/pi# ping6 2001:xxx:18:xxx::1
PING...
Hi,
I already used the sd_ble_uuid_vs_add for adding my base UUID in the internal table and it return a valid uuid_type (in my specific case it's 0x06).
I need to add...
I am using SDK 9.0.0 and i am having a doubt in bsp.h.In this header file when gone through this part of the code
#if (LEDS_NUMBER > 0) && !defined(BSP_SIMPLE)
#define...
For nrf 51 - DK , I flashed s130_nrf51_1.0.0_API
and then using keil uvision I copied over ble_app_uart_s130_pca_10028 and
tried to compile the code,
The code failed...
Hi,
What is the maximum voltage a level than can be given as an input on a pin on nrf51-dk? I've measured VDD at 2.91V. Is it from VDD-0.3 to VDD? If yes, is there a way...
Now I am trying DFU via BLE, some times I can do it successfully and I can do it as long as i want to, but the other time it shows "Error(0x85) GATT error" message and whatever...
I'm testing the DFU as described in this link developer.nordicsemi.com/.../a00086.html
after reseting in DFU mode, when I start the device discovery, I only get empty packets...
Hello
Quick question. With the nRF51, When in System On mode, should I manually disable peripherals to minimize power even if I'm not using the peripheral in question?...
Can I use RTC1, whitch is used by app_timer for button debounce, ble_conn_params and so on, to realize the time function (hours, minutes, seconds,day, week,month, yea)? And...
Hi, I'm not completely sure if this is a bug but I've been struggling with this for two days so I don't think this is related to my own application code.
The situation...
I tripped over what appears to be a change in the RADIO between nRF51 and nRF52.
For the particular case of issuing a STOP task when the radio is in Rx mode, there is no...