I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
nRF52840 NCS 3.0.1 MCUBOOT
OTBR on Raspberry Pi 4
I am running the OTBR on a Raspberry Pi 4 with the RCP on a dongle. I am running the coap_client on a nRF52840DK. I have...
Hey all,
Every time I flash, I get the following error message:
Error: One or more batch tasks failed: - [Probe] Device error: Memory access error at 0x00000000. Probably...
Hello, I wonder if it is possible to run the Thingy91 in MQTT-S with a certificate system to ensure the connection between the broker and the thingy. (CA, device certificate...
I followed the instructions in Lesson 9, Exercise 5 of the FOAT course. However, I am unable to complete the build process. I was wondering if I might have missed a step or...
I have enabled all the dependencies asked as below
CONFIG_IMG_MANAGER =y
CONFIG_STREAM_FLASH =y
CONFIG_BOOTLOADER_MCUBOOT =y
CONFIG_DFU_TARGET_MCUBOOT =y
Still...
Hi All,
In reference to my earlier ticket( https://devzone.nordicsemi.com/f/nordic-q-a/120183/question-on-immutable-bootloader-support-for-nrf54l15 ), I see SDK version...
I have a custom board with nrf5340 and want to run the radio_test sample on it. I have been able to compile and run the sample using the uart serial terminal, but I'm not...
Hi everyone,
I'm currently working on measuring the power consumption of the 9160DK board and following the guide: Getting started with current measurements on the nRF9160...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi
I connected RF Connect for Desktop to "nRF54L15_DK" in my Desktop
when I want to use Direct Test Mode,press Start test bottom,the log show "DTM setup reset command...
Hello everyone.
WE're trying to make a https connection with google.com and execute a GET request.
Wifi connection is working; DHCP seems to be working (my personal assumption...
Hello everyone. I am trying to develop a emulator for a Bluetooth low energy tv remote using raspberry PI. Basically I want to be able to use the raspberry pi as a TV remote...
Performance on hardware (cc3xx) is significantly slower than performance on software (oberon). Does anyone have a good explanation for this? I have also tested ECDSA and can...
Hello Sir,
I am currently working with the boards:52840dk and ncs:2.9.1
Regarding the issue of failed mcuboot upgrade after writing the upgrade firmware using flash APIs...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
