Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Hello:
Im rewritting a program from ST32F105RC to NRF51822.
In a part of the program of ST32, it checks if the interruption from pins 5-9 (EXTI9_5_IRQn) is enabled, and...
Hi,
I worked with temp sensor example and sofdevice s110 and something stuck on some function.
Anyway, I made readout from registers but softdevice blocks register access...
My nRF51 will occasionally lose connection to the computer, and I have to disconnect and then reconnect it before it will work. How can I reset the device dynamically, without...
I'm trying to compile a project I have for nrf51 on nrf52. I am running into errors with macros not being set.
For example:
error: #20: identifier "ADC_CONFIG_RES_10bit...
Hi,
I'm working on a sensor application that sends out fairly large quantities of data via BLE notifications. I understand how bluetooth works and have read and followed...
Hi,
I'm currently testing ble_app_uart on nRF51822 custom board. I connected it to nrf51 DK P19 and was able to program the hex file successfully.
But it doesn't run...
Hi, In your documentation you specify the maximum CPU temperature 85 DegC.
What problems could one expect after this point?
How much safety margain du you have on this number...
I'be been reading over and over the datasheet but cannot see how to dissable Enhanced ShockBurst features for my application which only requires basic one way radio.
I...
Hello,
I'm trying to program that module, but i can't do it correctly.
I'm using a program that works fine in nrf51 DK, but when I program this in ptr5518 my smartphone...
I want to port either the S210 experimental DFU over ANT_FS to serial DFU or the S110 dual bank serial DFU project to be S210 compatible.
I'm using S210 V4 and SDK 8
...
I would like to connect more than 8 devices to a single host. Therefore I would have to set the same role to multiple devices.
What are the implications of using the same...
HI,
I have some problems with the function sd_ble_gap_scan_stop(). I want to stop scanning into the RTC1 event handler but when I use this function (sd_ble_gap_scan_stop...
HI:
i have a question.if i use 51822 to connect other ble(ti or csr) ,could that be achieved.i have used ti dongle to scan 51822,but can't found 51822 device.if 51822 connect...
Hello,
In our project we use HID service. The difference between our HID and standart HID is that we use our own UUIDs. Our report charactestics include Report Refernces...
