I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello,
I installed the new nrfjprog but it fails to write my nrf51 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with
ERROR: argument...
Hi All,
I would like to design a wireless system using nRF51822 with an effective range >100m LoS and 5m under water.The system is used as a ON-OFF control device powered...
I am trying to run an Arduino sketch using the RedBearLab nRF51822. The sketch is designed to transfer data to and from a microprocessor and an Android device via bluetooth...
I'm currently want to use the NVM with ble device, when I tried to send values from the mobile app to be stored to the NVM, it doesn't work, I guessed that the problem that...
I want to write a device ID to the UICR registers at the same time as I flash the app code. I don't use Keil or that nrfproj.exe thing, I'm on a Mac. I have these targets...
Dear Nordic team,
I have the nRF51-Dongle and would like to use it with master control panel.
I did everything like already recommended in this tutorial .
The problem...
SDK 9.0
nRF51
PCA10028
I want use nRF51 gazell function one host multi device. Reference example code "gzp_dynamic_pairing",host and device can auto pairing .
But in host...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hey Guys，
Who can tell me what are the differences between the timer0, timer1 and timer2?
And if I want to set up timer interrupt in timer mode, the interrupt will be...
Hi everyone,
I took the example Ble_app_uart and I modified the Nus service for send data in Indicate mode.
With MCP I discover service and enable service (0x02->indicate...
Hi, every one,
In my application , we need to bond my device with host , and then our application will go to deep sleep by calling sd_power_system_off. When I wake up my...
Hi,
I have made some customs pcbs, the main one use the PCA10004 reference design and the small boards use PCA10000. I can get 25 meters on LOS (I think it can go far way...
Hello
Until recently I have been using a JLink EDU to program and test nRF51xx devices from Keil 5.14.
I recently bought a Ulink2 and would like to do the same but have...
Silly question, but I haven't gotten into a good rhythm with the debugger. Every time I try to use the debugger when a soft device is programmed, I can't seem to ever hit...
