I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello,
sorry to have to ask again, but from reading through all the posts I could not quite figure out how much current the SPI should draw when it is active and reading...
Hello everyone,
I am looking forward to 3rd party BLE modules in which I am interested in choosing Taiyo Yuden EYSHCNZWZ
I want to know that can we flash our code using...
I am using 3 nrf52 DKs with S132 and SDK14 / and SDK15 to try and implement a combination of the multilink and UART examples. I started with the ble_app_uart_c example and...
Hi All,
We are working on nRF52810 chip for on of our beacon project and we are using external antenna on board but
We are dealing with the Reason 8 disconnections.
...
Hey Team,
Can anyone please share the layout of the Program and Debug connector on the Thingy? I don't have a 10 pin SWD connector readily available and need to start...
Hi everyone, I have configured the LOG module to use it with the UART in view of debugging. I don't send anything in my loop but the UART send constantly these data :
<info...
Hello,
I am using sdk12.2.2 and nrf52832 customised board. My use case is as follows.
Suppose user enters in dfu mode trough app and for example user doesn't update...
I am working with nRF5_SDK_14.2.0 ble_app_beacon example using NRF52 DK. If I have directly copy pated the readily available examples\ble_peripheral\ble_app_beacon\hex\ble_app_beacon_pca10040_s132...
Hello,
I am building an application that doesn't need high-frequency microphone data.
I want to sample the PDM at 4K. It is possible to do so by changing the frequency...
Hi,
After i merged the light switch example in mesh_v1.0,1 sdk with UART example in nRF5 _v14.2 sdk, i'm trying now to put the status data recieved from server node to UART...
Hi,
We develop two BLE projects on NRF51822 and NRF52832 chips.
In both chips, for higher accuracy (better than ±250ppm) exists the option to connect the LFXO 32kHz crystal...
Dear Nordic Engineer,
I am working on sdk15,52840,ble app uart project,
i saw BLE_DTM_ENABLED in sdk config.
// <q> BLE_DTM_ENABLED - ble_dtm - Module for testing RF...
after flashing the board couple of times I get the following error:
device recognized by PC, I can see the drive created on PC
however I can not flash the device, and...
I am developing an IoT Gateway having BLE chip nRF 52840. The BLE of the gateway will connect to and transfer data to a BLE device having Vendor Specific GATT service and...
