I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I've made a custom board with nrf51422-QFAC, which I can program with nrf51-DK. I'm using SDK 12.3.0 and SD130, which is flashed to the custom board.
When I program the...
I'm trying to setup logging with printf() over UART and I got totaly blocked by following realy strange situation.
Let's have following very simple log_test.c:
Then...
Hi. I'm quite new to nRF programming. I successfuly solved how to compile/link/flash the software onto nRF52 DK using just a simple editor (Notepad++), the ARM toolchain and...
Wondering if there are any example/reference implementations of a bootloader for the nRF51822 that support Device Firmware Update over both UART and BLE? We've got the BLE...
Hi,
I have met problem when apply dfu of nrf52810.
I used dfu sample of 52810 from devzone link: https://devzone.nordicsemi.com/f/nordic-q-a/28471/about-ota-for-nrf52810...
I met a big issue when implement the voltage level switch. I used nRF52832's SPI to communicate with an ECG sensor which has 1.8V SPI. The issue is that, 3.3V signal from...
Having just got the DFU functionality working I got the task of trying to add NFC functionality to the application. The code side was not a problem since I got a c and h file...
According to the BLE 5.0 Specification :
"The Link Layer shall use the primary and secondary advertising channel
indices as specified by the Host, and the used primary...
Hi,
There is a bug in a Linux box (Mint x64) with the following configuration:
SEGGER Embedded Studio for ARM Release 3.34 Build 2017121400.34532 Linux x64.
Nordic...
Hi,
I am using ble_app_multilink_central and ble_app_uart central example for my application, i am combining these two example for ble_app_multilink_cenntral for BLE_NUS_C...
Hi,
I'm using the nrf_drv_twi driver (master) to communicate with a number of IO components, such as LEDs, buttons etc.
If my IO component does not respond (why is not...
I downloaded SDK 12.3.0 (seems to be it is the last supported SDK for PCA10028) and tried to use fats example, I changed pin configs to SPI's pins.
I also prepared my 16Gb...
Hi there,
I'm putting together a PoC board for a demo - in this case size matters and I've had to make some compromises for the sake of speed (which have increased footprint...
Hi,
After setting up constant carrier, how can one determine that it is working. With no modulation the receiver can't determine anything, can it?
thanks
Hi,
SPI use with SDK14.2.0 leads to very high power consumption (around 400 µA) on nRF52832 (QFAA). The same piece of code running with SDK12.3.0 has much lower power consumption...
