I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
So now that I understand the problem with overlapping asserted events on the GPIO port, I can't figure out the correct way to reset the sense field in the GPIOTE_IRQHandler...
Hi,
I follow steps in User Guide version 1.2. The Blinky project is working fine.
Then I program SoftDevice and after than compile and Download HRM using Kail
But led...
now,i pairing my peripheral and Communication read/write data. but have some issue for disconnect/reconnect .
1.disconnect: when i disconnect (call didDisconnectPeripheral...
Hi,
We are using Nrf51822 , pca1001 evaluation board.
when i flash bel_app_proximity code (by disabling led function in advertisement_star()),
current consumed by...
Hello Developers,
Just started with the nrf51822 and managed to install:Keil 5.05, Segger J-link, nRFgo Studio 1.16 and the Master Control panel. I also loaded the SoftDevice...
Hi,
I'm knowing the device_firmware_updates project in SDK and I want to know whether I need to program the softdevice when I do the device firmware updates over UART?...
I am developing a windows application, using the MasterEmulator api.
I am discovering BLE devices with scan parameter Active and Passive.
The result is that most of the...
HI,
when I used nRF51822 for 2.4G transfer ,I found that RX can't receive data in some direction .Can TX use two antennas and matching networks to work alternately in order...
Hi all,
I am currently working on a BLE project based on the PCA10001 evaluation board. I am trying to follow the nRF51 application note. I have done everything that the...
Hi
I'm using the nRF51822 and custom a service.I add 4 characteristic in the service and all of them
config to indication type to send data.Everything is Ok and sending...
Hi
I'm just starting with all this. My set up is a nRFgo motherboard with a nRF51422 DK attached (PCA10007).
I've installed all the tools of the toolchain as stated in...
I've just flashed the softdevice 5.2.1 and BLE Proximity sample app to my nRF51822. I presume any previous bond state on the device should have been wiped by doing this. ...
It would be nice if you could update Application Note 29 ("Development with GCC and Eclipse") for the nRF51822 to include instructions for Mac OS X.
I don't think it's...
Hello,
I developed a BLE based application using nRF51822 softdevice S110.
This application is very low consumption.
The device connects every 60 seconds, and can send...
