Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Currently nRF54L15 is being matched with LOW Q circuit and unipolar antenna. Because low Q circuit takes a lot of components and time when designing hardware. So I can remove...
We are trying to use extended BLE advertising with a nrf5340dk and are experiencing problems when trying to connect to an android phone (Android 13). Using legacy adverising...
Hello,
I noticed today that all the FOTA bundles I used to have on nRFCloud are gone !
Both the ones I added, and the "built in" ones (modem firmware).
Is this a bug...
Good Morning,
I'm currently developing an application for the nRF54L15 where I only need to send single BLE packages, therefore arising the need for keeping track of the...
Hi
I am developing an application where I need to update the BD address for advertising after each disconnection and on reboot. I know Zephyr stack has the API bt_id_reset...
I bought a tiny board on Aliexpress from HolyIOT. It comes with an nRF52832 and an LIS2DH12 accelerometer. The silkscreen on the board says HOLYIOT-21011-v1.0.
This schematic...
Hi, I recently started using nrfutil with the deprecation of nRF Command Line Tools. In one of the recent updates the change log lists:
2025-03-24: Version 2.8.4 Added:...
In our project, we referred to the nRF52832 Application Reference Circuit Schematic for QFAA and QFAB QFN48 with internal LDO setup . However, during actual testing, we found...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hello team, We are currently working on a project that used nRF52833-QDAA-B as the MCU chipset. We have followed the circuit configuration 5 for our test case. Our SoC is...
Hi,
MPSL radio notification API has been removed from the nRF Connect SDK v2.6.0.
Is there any alternative way to get radio notifications?
Regards,
Narendra
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
We are developing a project that runs BLE, the Nordic Uart Service, the Nordic Distance Measurement toolikt and Async UART (NCS v2.9.0). The Peripheral device shall advertise...
Hallo,
we are using the nrf5340 and the ncs Version 2.6.1.
I activated the software downgrade protection as described here Downgrade protection (nordicsemi.com) .
Then...
