hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi Support Team
We want to develop an application of combining a PDM microphone and a nRF54L15. When we speak a word into the microphone, the nRF54L15 will perform a corresponding...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Hi,
We are working with a custom board that uses the nRF54L15 and I seem to be getting a lot of errors (but not always) related to memory access error when flashing the...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello,
I've tried to compile the experimental_ble_app_hrs_pairing_nfc example using Keil uVision. The example requires the NordicSemiconductor::nRF_DeviceFamilyPack version...
Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hi Nordic Team,
Setup:
Board: nrf54l15dk
NCS: v3.0.1
I use LOG_INF and printk to print data in minicom or Serial Terminal v1.4.3 from Nordic. Printings seem misformatted...
Hi,
I am porting a SDK 2.6.0 project to SDK 2.9.0. It gets built without errors but when I try to run it after flashing I get the following.
I am not sure where to start...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
System Info: Hardware: M3 Max OS: Sequoia 15.3 Following the instructions outlined in the readme of: github.com/.../nrf-docker Docker fails to build an image on Apple Silicon...
I've developed a custom Matter application based on the Matter samples in the Nordic Connect SDK, targeting the nrf52840. I developed the first version using the nrf52840dk...
Dear Nordic Semiconductor Support Team,
I hope this message finds you well.
I am currently evaluating the nRF52840 for use in an industrial/automotive application and...
Hi Nordic team,
I’m currently testing UART communication on nRF54L15 with NCS 2.8.0 , and I’ve encountered an issue I’d like to ask about.
When using UART20 configured...
Hi
Does the nrf-sw-pwm driver work on the nrf54l15. I am porting code form the nrf52840.
My output does not toggel, 0% and 100% does work but noting else.
