Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Device Information
Module: FANSTEL BC832 Bluetooth Low Energy 5 Micro Module
Chip: nRF52832
Firmware version: Default AT firmware
Current MAC Address: ef30:0a:cab132...
Hi,
We designed our custom board using nrf54l05, and tried to flash it using segger J-lInk as well as using nrf54L15-DK Debuger out port using nrf connect Programmer utility...
Hello community,
I'm currently working on setting up SPI communication between two nRF5340 DK boards , but I'm running into several issues.
SDK Version 2.9.1 : I couldn...
Hello Sir,
I am currently working with the boards:52840dk and ncs:2.9.1
Regarding the issue of failed mcuboot upgrade after writing the upgrade firmware using flash APIs...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
When using Bluetooth AOA, I configured only two antennas to collect IQ data. Below are the curves formed by the 37 IQ data points collected from the two antennas during the...
Hi.
I have been investigating how to use GRTC and LFXO for LFCLK with nRF54L15DK. In my goal, I would like to make the Intermittent application with sleep and GRTC that...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
I started encountering a problem when calling bt_enable(ReturnCallBack) . The ReturnCallBack function returns the error ENOBUFF (105) . I assume it's a memory allocation issue...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi, I have two firmware images: A and B which I need to make compatible for OTA (DFU over BLE using MCUBoot - the standard process described in the devacademy course ). They...
I'm playing a bit with MCU boot and folowed the tuturial . When I compile the sample with mcuboot from Zephyr, it works fine for the 52840DK, but when I try to compile for...
Hello,
I'm trying to enable RTC2 for nrf52840 DK to use as a date time clock and set/get over SMP protocol. RTC0 is used for MPSL, RTC1 is used by the system.
I configured...
Hi everyone,
I’m using a custom board (a tracker) that can travel at speeds up to 65 km/h and transmits data regularly every 200 ms. I expect, therefore, that the inactivity...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
