pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hi,
I’m working with the Wi-Fi station example on the nRF54H20 using SDK v3.0.0, and I’m encountering a critical issue when trying to bring up the nRF7002EK Wi-Fi module...
I have an NRF52 devkit and trying to install the "blinky" sample for the first time, using VS Code.
I can build the firmware, but when I try to flash I get these errors...
Hi,
I am currently working with the channel_sounding/connected_cs sample for nrf54l15 and I keep getting the error: Not enough memory to store step data (530 > 512). I tried...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
Hi,
I configured for using security BT_SECURITY_L2 for a device that I had previously configured for using BT_SECURITY_L4. When I try to connect with an Android phone that...
Hi Nordic team,
I'm trying to configure the GPIOs to operate at 3.3V using the nRF Connect for Desktop's Board Configurator tool (v0.3.10). The tool works as expected...
Hello, I am trying to use the subghz template in ncs 2.5.2 but I am running into an issue when enabling NanoPB. When enabling NanoPB with CONFIG_NANOPB=y the application faults...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
Hi,
I succeeded in implementing Channel sounding for multiple devices (based on previous samples). But now there is a little difference in how the data gets collected (buffer...
While using PAWR, we see the above HCI event.
The subevent data is then empty.
Do you have any advice for debugging this?
There doesn't appear to be any helpful logging...
I have a project using BLE as a central on an nRF5340 to connect to several devices. For factory test I am being asked to implement something that can be used in the factory...
Hi, my code will return ATT error code: 0x0E cyclically
I have check some tickets and try to update my central device to
Hoever, it still cannot, the error is like...
