In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
Hi,
I need to implement low power mode in my project with an nRF52832. From a general perspective, I want to:
1) boot the device,
2) initialise stuff/peripherals,
...
Hi,
I am analyzing the issue that the BLE module can maintain a relatively short connection distance. Besides the transmission power and frequency offset, I also take...
Hello, guys, I am working on direction finding using nRF5340 DKs and v.2.9.0 SDK. I found that an antenna array is required to find the direction using nRF5340 DKs. So is...
We have been fighting with the Distance Measurement Toolkit for a while (see other ticket ). As we needed to move forward, we started the implementation of LE Secure Connection...
I use nRF5SDK1230, S130nrf51201. Firstly, I flash ble_app_beacon in PCA10028, it works good. then i flash the same program in custom board(nrf51822qfaa) without any change...
Dear Sirs
I try to read SoftDevice version using
ble_version_t version; sd_ble_version_get(&version);
As I understand I get version of SoftDevice in field subversion_number...
Hi Nordic team, 您好，北欧团队，
I am developing nrf54L05 in VS code with NCS.I want to configure the SEGGER_RTT_printf to my project.Is it correct to change the CMakeLists.txt...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
hi, any SMBus support on the nRF54L or nRF54H?
many recent charger + (in-pack) pcm/gauge-IC's talk directly to each other, while this being smbus 3.0/3.1, utilizing notify...
I have built and flashed the openthread/coprocessor sample using VS Code specifying "nrf54l15dk/nrf54l15/cpuapp".
I then tried to run it (on Ubuntu 24.04.2 LTS, x86_64)...
Hi,
I am trying the system_off sample of Zephyr version 4.0.99: https://docs.zephyrproject.org/latest/samples/boards/nordic/system_off/README.html
The sample works...
Hello,
Both nRF5340 and nRF7002 list minimum storage temperature of -40C. We would like to understand what environmental testing has been done to reach this storage range...
Hello,
I've received a strange error when attempting to send the %BANDLOCK, any idea what it could mean? I don't believe 65536 maps to any of the error codes here , but...
