Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello，
I have a problem with using custom external Flash. QSPI communication.
nrf52840 + NCS2.9.0 , sysbuild.
Flash chip is GD25Q32, datasheet link
An error occurred...
Hi
We know PMIC nPM1300 can transfer battery information through I2C to nRF54L15 to run fuel gauge algorithm
Can we user other PMIC(like MAX77654) that also have I2C I...
Hi Sir,
As check below link, the battery profile can support on non-Nordic MCU.
(+) Does the PMIC nPM1300 support Fuel Gauge feature for MCUs outside the nRF SoC family...
Hello Nordic forum,
I must not quite understand how CoAP callbacks should work. Would anyone be able to give me any advice as to why my modified coap_client results in undefined...
Hi,
Im currently trying to add FOTA via BLE to my project.
To get familiar with this i wanted to add FOTA as described in the nrf connect intermediate course lesson...
I tried to find an explicit statement whether a new IMEI needs to be written to nRF9151.
These sources state that nRF91x1 ships without IMEI and it needs to be written:...
Hello, I have a project based on nRF9160 and nRFCloud (CoAP), and uses a SIM from 1NCE. This SIM allows to connect to 3 different MNO at my location in France (Orange, Bouygues...
By default the GRTC peripheral is not cleared when started via sys_clock_driver_init . This is because nrfx_grtc_init calls nrfy_grtc_prepare , however NRFX_GRTC_CONFIG_CLEAR_AT_INIT...
Hi I want to know if I can use the nRF52850-DK to flash the Xiao Sense Plus from seeed? I am following the following tutorial which says I need to use a J-Link but that's...
Nordic published a great blog in 2022: "Comparing range with Bluetooth Low Energy of the nRF21540 DK and the nRF52840 DK." It clearly explains the range capabilities of the...
I am new to Zephyr RTOS . i have a breakout board of Max32664D from protocentral interfaced to nrf52840 development kit . i want to get started with this sensor hub max32664...
What is the default transmit power of the nrf5340 when performing an AoA test in connected mode? How do I change its transmit power to perform AoA accuracy tests at different...
Hi,
I tried to change security level, but it's not changing.
When i set CONFIG_BT_SMP_SC_ONLY =y, it's working well with security level 4,
but i want to change mode1...
Hello everyone,
I am a beginner looking to dive into the world of HID (Human Interface Device) development, specifically using the NRF52840 microcontroller. I recently...
