I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
Hi there!
I'm in the process of updating our codebase from 2.4.0 to 2.6.4. We are using the nRF52840. My plan is to do this step-wise, following the migration guides for...
I am currently in the process of filling out the 18031 RED Cybersecurity certification documentation. I am currently analyzing the security vulnerabilities list of NCS v1...
I’m working on a BLE setup where:
A Nordic nRF52840-DK runs as the Central (it scans for devices with a specific name, then initiates a connection).
A Raspberry...
Hi,
I'm currently working with the Thingy:91X and would like to measure the total current consumption of the entire board using the PPK2. I understand that the PCA64165...
I am currently working on a 3D game in Unity (made in C#) and I am asked to connect a Nordic Thingy:52 nRF6936 (based on the nRF52832 SoC) to Unity to control a part of the...
Hi,
I'm developing custom firmware on the appcore and netcore. The netcore runs BLE controller, as well another custom IPC service to communicate between the appcore and...
The OSCILLATORS documentation says:
" The device starts at 64 MHz. For 128 MHz, it must be configured when the CPU starts and before any peripherals that use the high-frequency...
Hello,
I was given an existing code with a possible bug in it relating to RAM retention and I'm trying to make sense of what I'm seeing. I am using NRF52832 with SDK 17...
Function: Now we have developed a function similar to usb file upgrade on the application side by ourselves (which requires operating bank1, writing the Settings page, involving...
Hi,
we are looking into incorporating a NRF52 module into our control units, but to allow extending the antenna position away from the case through male-female SMA cables...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi There
while extending the actual Sofware with more flash entries i discovered that the capability of provisioing devices decreases, and end up in a hardfault.
Is there...
Hello
In my board I am using an ic as a switch to control the routing of the TX and RX pins of the UART, due to the fact that the nRF9160 does not have more than 4 peripherals...
Hello, I am developing a project that involves authentication over NFC, and need to store a private key in TrustZone. I found the psa_crypto zephyr sample in the sdk, which...
