I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
i am working using NRF52, s132, sdk11, freertos.
for fft , i used "arm_rfft_fast_f32(...)" in cmsis-dsp library.
and i inserted a fpu interrupt.
NVIC_SetPriority...
Hi.
I'm using PCA10040.
I'm trying to control GPIO.
But I can't control PIN 09, 10.
Let me show you my source code.
int main(void)
{
/* Configure LED-pins as outputs...
Hello!
I have encountered an interesting issue:
When I use compiler flags (GCC CFLAGS) -Os or -O0 together with -flto the pstorage function pstorage_block_identifier_get...
After I combined the Timer example and ble_app_uart, the program is hanged at below function when init the timer. Please tell me why
__STATIC_INLINE void nrf_timer_event_clear...
I need to turn off a GPIO after 8 hours of it being triggered.
I was reading about changing the prescaler to allot for 8 hours. I did the calculations and came up with a...
I have purchased a red bear lab ble nano board with nrf51822 and a PICTAIL board with microchip RN4020 chip. i have set Tx power 4 for both boards. The rssi value shown in...
This may just be a preference or architecturing question but I thought I'd ask in case there was anything I'm not thinking of, or benefit of one or the other.
I have 2...
Hello,i am find an interesting phenomenon recently.I have a Nordic 5182 device(role as peripheral) and bonded to an iOS device(role as master),when i put the iOS device near...
I'm wondering, is it possible? This is what I think it will be like if it were going to be implemented:
Acquire the firmware from a host somewhere.
Since the payload...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am working with nrf51822 MC. In my Transmitter code, i am using in low power mode. I was enabled the low power in my code (__WFE(), __SEV(), __WFE()). I measuring...
Hello, I need HID device with NRF51 Dongle.
when NRF51 Dongle insert PC, PC will check it as HID device.
So, could anybody can share suggestion how to add HID on NRF51 Dongle...
Briefly:
Is it possible to switch LFCLKSRC to the internal RC from Xtal with WDT or RTC running? It appears I am only able to do this when Xtal is generating LFCLK...
I am trying to build a ibeacon device, but when iphone in "background mode", it can not get data from ibeacon device.
I used test code :examples\ble_peripheral\ble_app_beacon...
I am working with the nRF51 (PCA100028) dev kit and the nRF51822 beacon to monitor the RSSI of the beacon via the nRF51. To do so, I installed nRFconnect and Master Control...
