Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I'm following the tutorial Development with GCC and Eclipse
I could compile and flash existing project that attached to tutorial.
Now I can't understand what to to while...
Q1: how to do network commission? do we have to use an Apps to do commission linke CSRmesh? or it is already in a same network if we configure all nodes use the same access...
I have been using pc-ble-driver in Linux (downloaded and compiled from github here - github.com/.../3316c0c306257a825168751964f814cb95fc0d74) with our custom C++ application...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
Hi All,
I am using nRF51822 for my application.
how to change the App timer Interval dynamically means i have to change the timer interval before timeout.
sdk132. nrf52832 board
Try tutorial "Development with GCC and Eclipse" devzone.nordicsemi.com/.../
.
All the time I'm persecuted by error
/// *** No rule to make target...
I hava a BLE device which can be found by andrioid 4.4 and 6.0 smartphone, but cannot be found by apple iphone5s iOS 9.3, what could be possible wrong with it?
Hello all,
I am using the pc-ble-driver-py python bindings (which depends on pc-ble-driver) to test my BLE peripheral
It works fine for reading and writing characteristics...
Hi,
I use the Current Time Service to get back the time from a smartphone to have a real time clock with a timer.
On the current time service example, the value is read...
Hi:
I compiled the ble_app_cts_c project of the SDK12 using the Segger Embedded Studio having as target the PCA10040 board (S132 stack). After spending some time to convert...
follow the tutorial I'm stuck in the step of removing "retarget"
I don't have such option
I have this one. Should I just remove retarget.c directly via context menu...
main.c Hi,
Currently I am using "ble_app_uart" base example to understand how ble works. I have gone through bsp and other header that related to button events.
There...
Hello developers,
I am trying to use ble_hrm service example with actual heart rate from the module pulsesensor.com ( http://pulsesensor.com/ )
I am able to read raw data...
Hi,
I am working on one application in which I want to change pin number assign to channel 7 of SAADC in nrf 52. I am using Rigado BMD 300 module in my application. As...
Hi,
i want to use a current time service in nordic app (nRF Toolbox) for the bgm profile.
I see, that when the cts service is not found, the micro reset. Why?
Someone...
