I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
On the nrf52dk development kit, I want to power the target nrf52 from an external supply without powering the interface mcu (the debugging probe). How do I wire that? I don...
I'm trying to add nRF_Drivers files to Segger studio project, based on nrf51,51422(10028) examples. I added path in preprocessor user definitions and I added file like nrf_drv_lpcomp...
I set up my PWM Driver like this:
nrf_drv_pwm_config_t const nrf_drv_pwm_config =
{
.output_pins =
{
BSP_LED_2 | NRF_DRV_PWM_PIN_INVERTED, // channel 0
NRF_DRV_PWM_PIN_NOT_USED...
Hi,
I would like to test my C code with bootloader over air by BLE. I am using nrf51822 with soft device 110. Does Nordic Company is sharing any application which can bootload...
So this might be one of the most confusing issues i've come across sofar. We're currently developing a product based on NRF52 (more specifically NRF5283 QFAAB0) with a custom...
Is there firmware available as binary file that can be loaded to the nrf52832 that allows connectivity to is as a UART HCI compatible device?
Would the same firmware be...
Hi,
I am using "nRF Toolbox -> DFU" to change an application on my BLE module which contains; nRF52 device, SDK->v11.0.
I am using ".hex" file to load the application...
iphone5_b.psd m370_android6_b.psd long_write_error.png I using SDK11. I porting nus profile to my system and make a customer's UUID. I use Lightblue on iPhone 5 to connect...
Hi,
I would like to know, by using nRF528322 Development Board can we dump the code into another hardware like custom nRF51822 microcontroller..??
If Yes, What are the...
hi , need a urgent help on small problem but really not getting ahead bcos of it.
I'm using NRF52, SDK v11 , Software Device s132.
I'm calling sd_ble_gatts_value_set() like...
The struct type nrf_saadc_config_t is defined in ../hal/nrf_saadc.h but is not referenced anywhere else in SDK v12. Thus it is either cruft, or more likely, the function nrf_saadc_init...
Hi.
Is it possible to use SPI slave and SofDevice at the same time? I try to do device which status will be read by master uc by SPI. I'm using nRF51422(rev.3), SDK10.0...
Hi All,
I am working on nRF51822, i have questions about BLE passkey security:
1- The pass key is for GAP or GATT services?
2- The BLE have few layers of data: Profile...
Could you confirm s130 data for Segger Studio Section Placement Macros FLASH_START=0x1b000
SRAM_START=0x20002800 ? This works for sdk11, somehow goes to hard fault handler...
