Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello community,
I'm currently working on setting up SPI communication between two nRF5340 DK boards , but I'm running into several issues.
SDK Version 2.9.1 : I couldn...
Hello,
This ticket actually build upon the previous ticket I did here Possible Bug: Cellular modem sample with nRF9151 running SLM .
To recap, running cellular modem...
Hi Support Team
UART20 of nRF54L15 can't work when setting P2.02 as TXD and P2.00 as RXD when I test the central_uart sample of NCS V2.9.1. I find that the SPI00 has used...
I build and flash the wifi example "Wi-Fi: TWT" source code to the nRF7002-DK， and it work well and print is right:
[00:00:06.764,190] <inf> twt: ================== [00...
The 9161 has 256 KB of RAM, but while building the application, it reports that only 32 KB is available for the application. If I create some large static buffers (e.g. 40...
I've tried the following with the Quick Start app v1.2.0, v1.1.0 and v1.0.1. The log below is from v1.1.0, if I recall correctly. All logs are about same. Programmed the Asset...
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
Hi,
I am currently working on the Matter ecosystem for an IoT home automation product. I have referred to the Nordic technical documentation on the Matter Bridge, available...
hello everyone,
I built an application based on the peripheral_uart sample running on the EV-BM833 board. The application includes the Nordic UART service.
Using the nRF...
I am in the process of migrating to NCS 2.7. My project includes NSIB, MCUBoot, TFM, and the application. Everything works fine with multi-image builds.
However when using...
I am working on an nRF52-based BLE peripheral (beacon) using the Nordic SDK. I want to implement functionality where the advertising interval can be updated dynamically from...
Hi Support Team
We want to develop an application of combining a PDM microphone and a nRF54L15. When we speak a word into the microphone, the nRF54L15 will perform a corresponding...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Hi,
We are working with a custom board that uses the nRF54L15 and I seem to be getting a lot of errors (but not always) related to memory access error when flashing the...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
