Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
For VDD-nRF in the nRF54L15-DK schematic When I check the schematic, I can't tell which part is internally generated.
When I check the actual board, VDDM_nRF and VDD_nRF...
Hello,
I'm currently testing BLE Coded PHY by using extended advertising.
I used two nRF52840-DK and nRF5 SDK v17 with compatible softDevice.
I've checked that the...
Hi,
I am running Matter TH.
Among them, there is an error in the TC-DA-1.2 test step 6.9 certification_type check.
The reason for the error is that the certification_type...
Dear Nordic company,
I am writting to you in order to discuse some trouble with TCP server that I am trying run on Serial LTE modem application.
I am able to create...
Hi everyone,
I am currently studing to flash the MDBT50Q-DB-40 demo board from RAYTAC. I used the following site as reference. https://docs.nordicsemi.com/bundle/ncs-latest...
Hello,
I am currently measuring the current consumption of the Thingy:91, specifically when running the Asset Tracker v2 application. I observed that the average current...
Hello, I’m currently working on a PDM microphone project using the nRF52840 and the Zephyr RTOS. I’ve been testing the official dmic example from Zephyr (located at ncs/v2...
I am currently developing firmware on Qorvo's DWM3001C module , which integrates the Nordic nRF52833 . I am using nRF5 SDK 17.1.0 and the SoftDevice S140 .
My base project...
Sending array unit8 type data using BLE failed, and attempting to take 2 bytes of data from the array and send it also failed. Does anyone know what this log error means?...
Hello,
Since a few days ago, when I start VS Code, I get the following warning:
But when I check the settings in VS Code, v1.x.x is not there.
What could be the...
I have a Raytac MDBT50Q-CX and cannot seem to flash it correctly. The flash succeeds, but the device is no longer recognized by Windows or (raspberry pi) Linux.
My goal...
I am currently working with the nrf54l15, I have both the DK and a custom board I designed. I am running into issues with the uart00 peripheral when using custom GPIO pins...
Hi,
I am using nRF52840 DK and I am following Nordic Academy nRF Connect SDK Fundamentals. I installed SDK 2.9.1 and toolchain 2.9.1
I copied the sample blinky and encountering...
Hi everyone,
I'm using the nRF54L15-DK and trying to implement a simple low-power cycle where the board:
Measures sensor values
Sends them via CoAP over OpenThread...
I am migrating from a child_image type project to the newer sysbuild system used in ncs v2.9.0.
My application is based on the ncs nrf5340_audio application, but my application...
