Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, guys
I'm facing some problem in RF transmitting. While I used 51822 board being the device and compatible to nrf24LU1 as dongle. To analysis the problem, I need information...
Hello,
i am working with the s110 softdevice and built up a bluetooth communication. I wanted to reduce the number of advertising channels and read about the use of the...
Hi,
I need to send some additional information in advertising.
According to Core Specification Supplement v4 A.1.11 it is possible to use also 128-bit UUID in service...
My keyboard can't work some time,then I read back the hex from device. And I find that there are 4 byte be changed.
if I modify the left 4 red bytes to right. Then programm...
In my opinion, S120 can only acts as central role and can not be discovered by bootloading sponsor which is usually a PC program. More development work is needed if bootloader...
I am trying to run the bootloader example that comes with the SDK 5.2.0 using the softdevice S120 on an evaluation kit, but I am getting an error at the pstorage_init() function...
I'm trying to emulate an nRF24L01+ SPI slave interface with an nRF51822. The nRF24L01+ interprets the first byte in the SPI transfer as a "command", and the data that it will...
Hello,
we experience the situation, where we are able to flash a softdevice (s210) once. After the softdevice is flushed, subsequent attempts to flash the softdevice fail...
I was looking at the product brief for the nRF51922 - which states the SoC can handle both BT BLE and ANT concurrently. The product brief states:
Pin-compatible hardware...
Hello,
I have problem with two nRF24l01+
First is connected with a mcu to a sensor.
Second is connected with a mcu to a pc throught usb.
I want to get data from...
I'm looking to be able to plug my usb dongle into my computer and communicate with an application for users to use. In this communication, I would want to see the different...
Hi,
I would like to extend ..\nrf6310\s110\ble_app_beacon example and add the possibility of switching from beacon mode to configuration mode and then add a few services...
Hi,
I'm currently trying to use the PWM Library in the LED Button Example, I was able to get the LED to blink with the PWM library when USE_WITH_SOFTDEVICE=0, but ofcourse...
Hi all,
I am using sdk 5.2.0 and s110 softdevice 6.0.0 on PCA10006 and nRF6310 platform for development.
I encounter unpredictable BLE link loss issue. In my application...
Hi,
Edit: Development with Eclipse and GCC
I'm rather new to working with eclipse and C.
I already have a problem with the first step of your explanation: (I'm using...
