Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
I was following instructions from this and this post, but I'm not yet able to build with the following combination: CMakePresets.json + west + sysbuild.
I'm using this west...
Dear Onomondo Support Team,
I am currently experiencing an issue with my Onomondo SIM card — it is unable to register on the network when used with the nRF9151 DK board...
NCS 2.9.1 - NRF5340 DK
I've developed the gppi one_to_one example to try and create an asymmetric pulse that I can control with the Timer compare registers. It boggles my...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
I am following along this example on your website: Exercise 1 - Nordic Developer Academy , and currently trying to complete this excercise: Exercise 1 - Nordic Developer Academy...
Hi, I tried to migrate my project from nRF Connect SDK v2.5.3 to v2.9.0, switching to sysbuild and creating my own board definition instead of using a overlay file.
I decided...
I have a custom board (nrf5340) and can debug it, but it will not print to J-Link RTT Viewer. The main looks like this and I tested with a breakpoint on the LOG_DBG using...
Hello! I'm looking for a way to include fast charging capabilities in my product, while still allowing USB2 data to pass between any host PC and the nRF52840. As I understand...
Hi, I have custom board with nrf54l15. Im using sdk 2.9.1 and nRF54L15-DK as debugger/flasher. Im able to flash firmware correctly using SWD, or do nrfjprog --recover, but...
According the nPM2100 page "nPM2100 comes with exceptional software support for Nordic’s nRF52, nRF53, and nRF54 Series" but doesn't mention "nRF91 Series".
Currently I...
Hello, I searched the forum for similar issues and found a few, such as
I am currently implementing a PSRAM is66wvs4m8 on the Thingy 91 via SPI, using SPIM3.
The problem...
I need both zephyr power device management and the low power features of LPUART in my project.
However, enabling PM_DEVICE raises idle current consumption by quite a bit...
hello to all.
i been strugling the last couple of days to make a simple PPP connection from a debian12 laptop to the internet passing trough the nrf9151. I followed the...
Hi,
I want to produce a pulse with 4 seconds length from p0.25, but i am failed.
#include <zephyr/sys/printk.h>
#include <nrfx_pwm.h>
#include <hal/nrf_gpio.h...
Hi, I would like to have some suggestions on my PCBA design for nrf54L15 chip. Please review it and give some suggestion moving forward. I am making this PCB to use this with...
