Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
In s210 there are functions sd_flash_page_erase, sd_flash_protect, and sd_flash_write. There is no sd_flash_read.
How do I read from flash? I can write to is using sd_flash_write...
Hi
I just want to create a custom service with a characteristic, which sends "n" (upto 200) bytes at same time and this bytes are are written to a SD card via SPI
So...
Hi, I have been using the nRF8001 Arduino SDK with nRF8001 chip. I wanted to set the data for the different services I'm using and thought I would go ahead and use the services...
Dear sir
Now, I am trying multi-link examples at SDK5.2.0 S120 example. I found s120 central only can receive one byte data from s110 multi-link peripheral. Could we modify...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hello,
I have some problem with NRF24L01+. I'm trying to make bidirectional connection between two devices with this chip. When I'm sending payload with ACK, TX_DS interrupt...
Dear nRF Gurus,
I made a board with nRF8001 and PIC24F to stream some sensor data to a computer. I have also developed a simple Mac app to communicate with my board. (similar...
Hello,
I am redoing some experiments with 2 pca10001 and the ble_hrs example (with s110, s120) !
What I would like to do is that the s120 side displays the power received...
I'm designing a small board with an nRF51822. I'd like to use a 'meander' PCB antenna similar to the ones on the Evaluation Kit and 'dongle'. Is there a definitive guide ...
I'm trying without much success to write something fairly simple. Basically connect a signal to a pin, and run a function whenever that pin changes state. What's confusing...
Hello all,
I am debugging my nrf51822 application using evaluation board and keil debugger. I have uncommented the ble_debug_assert_handler in app_error_handler. When error...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
