I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
We have a design in EVT and we're preparing for FCC testing. It's a dual radio board with nRF52840 and a Semtech LR1110. Therefore, we need both to be active and transmitting...
Hello everyone,
I'm developing an application using the SX128x radio with the LoRaWAN Basic Modem.
The project runs successfully on a custom board based on the nRF5340...
Hi,
SDK: 3.0., nRF54L15
The application is Matter + BLE dynamic multi-protocol + battery powered sleepy end device. Current Application(Matter/Thread + BLE + Firmware...
Hi Nordic Team,
We are using the MIMXRT1050-EVK as the host and the nRF7002EK as the Wi-Fi module with an SPI connection. However, we are encountering frequent errors that...
I’m using the Zephyr nordic,npm1300-charger driver on an nRF52840 to control the nPM1300 PMIC charger. At runtime I need to be able to turn charging on and off—on command...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with two specific exercises: l2_e3 and l4_e1 . Other...
Hello, I can commission bulb and switch pass, then I refer this link( acl and bind ) to write ACL and binding both, eventually I can use switch to control bulb!
But I have...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hi,
I need to implement low power mode in my project with an nRF52832. From a general perspective, I want to:
1) boot the device,
2) initialise stuff/peripherals,
...
Hi,
I am analyzing the issue that the BLE module can maintain a relatively short connection distance. Besides the transmission power and frequency offset, I also take...
Hello, guys, I am working on direction finding using nRF5340 DKs and v.2.9.0 SDK. I found that an antenna array is required to find the direction using nRF5340 DKs. So is...
I use nRF5SDK1230, S130nrf51201. Firstly, I flash ble_app_beacon in PCA10028, it works good. then i flash the same program in custom board(nrf51822qfaa) without any change...
Hi Nordic team, 您好，北欧团队，
I am developing nrf54L05 in VS code with NCS.I want to configure the SEGGER_RTT_printf to my project.Is it correct to change the CMakeLists.txt...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
hi, any SMBus support on the nRF54L or nRF54H?
many recent charger + (in-pack) pcm/gauge-IC's talk directly to each other, while this being smbus 3.0/3.1, utilizing notify...
