I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi
sdk:17.1 ble_app_uart(esb_timeslot))
When I was conducting the integration test between my device (nRF52832) and the external device (nRF24L), I encountered a problem...
I am trying to follow the first lesson of https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals
But I have several problems and I can not find out how to fix...
Dear Nordic:
I used V2.8.0 SDK to build light bulb, and I have commissioned bulb A(node id: 11) and bulb B (node id: 11) successfully!
Then I used below command to add...
Hi Team,
I am working on a project where we are using nRF5340/nRF52840 uC IC from Nordic. from past 2-3 years we were using this software hassle free but now due to to some...
I am using nRF9160 to develop a product for a client that requires displaying the name of the current carrier on the screen. According to the AT instruction manual of the...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
I am trying to integrate nRF7002 into my application firmware, by using the "wifi/sta" example in NCS3.0.1.
My application has CONFIG_NRF_SECURITY=y and PSA enabled and...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
Hi,
I have a question about the following registers:
・XOSC32M.CONFIG.INTCAP
・XOSC32KI.INTCAP
For these, the reset value is as follows in the data sheet:
I...
I am using NCS 2.9.0 and latest extensions for VS Code.
To reproduce, use Mac, create a new app from Blinky sample, build it and open "prj.conf", then wait a few minutes...
I have downloaded nRF connect setup V5.1.0 and nRF command line tools V10.24.2.
downloaded nRF connect extension , SDK pack and tool chain in VS code.
I added the build...
Has anyone else had problems with adding build configurations for workspace applications using the VSCode GUI interface? Initially I clone the repo using CLI-based west commands...
Dear Nordic Teams :
I find the NFC current and find the current is quite large in the datasheet version 0.8. The value is much bigger than nRF52840. Is it correct?
Hello,
I am fairly new to the development with nRF and am having problems getting sensor data from a connected BMP280 to the nRF5340 audio dk.
The first thing I did...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
