Hi NRF support team, We are developing a custom board based on the NRF9151 SIP. I am experiencing some issues in provisioning the device to the NRF cloud. On the 9151-DK i...
Hi,
I am not able to program an Acconeer xm122, which is powered by an 52840. It is mounted on the Acconeer xb122 shield. My nrf52832DK is connected to the shield using...
My AD data is defined with macros as such:
I need to change the manufacturer data then update the advertising data using
My question is: How do I get a pointer to...
I have an NRF9160 system running and I see mention of " The nRF9160 PWM peripheral can capture the period and pulse width of an external PWM signal" but was a little confused...
Hello, I am encountering an issue while setting up an OpenThread Border Router (OTBR) using the following hardware: nRF52833 board (flashed with RCP firmware) nRF52840 board...
Hi
custom board using the nRF9160, toolchain version v2.6.0, mfw_v1.3.6.
Sorry I can't provide a decrypted modem trace, but I hope the screenshots are enough to show what...
Hi, I am working with nRF52 DK (52832), and the issue I am facing is that i am unable to increase the data size of data SPI -DMA can receive. Currently it is configured at...
Hi
I have working module which communicates via uart with another module. It works good, unless it is heated to 40C. After that temperature UART communication is not correct...
Hi Engineers!
We made our own ten (10) PCB's with nRF52840 MCU onboard fully according to "Circuit configuration no. 3":
1. LDO only mode (VDDH connected to VDD connected...
I have a custom circuit with nrf52832 which I am trying to program.
All i/o pins seem to be working fine except pins P0.06 - P0.10.
I'm testing it with mbed (digitalout...
Hi,
Thanks for taking the time looking into issue.
We are using Keil uVision 5.14.
Our target is a custom board (BMD200 eval Module based on nRF51822)
We were able to...
Hei guys,
for a new custom board based on nrf52832 where i have to minimize power:
have an external Li-Po battery, with a cutoff @3.0v, so the range will be 4.2v...
blesc_pairing_dhkey_check_failed.zip
Hello,
I used the example ble_app_multirole_lesc and paired with nRF Connect app. However I got the error message (in Bluetooth...
Hi!
So I have my GATT value of a service that I would like to update.
Sadly that value always stays at the initial value.
Below you can find my update function.
uint32_t...
I am using SDK12.0.0. ble_app_uart example, and I have change the clock to using LFCLK RC. I know from nRF51822-PAN_v3.1.pdf that we need to calibrate the LFCLK RC after reset...
I've managed to overcome all the quirks in setting up Eclipse/gcc development with the nRF52 PDK (PCA10056), and I can build the sample projects just fine. Here's my issue...
I arrived at step 8 in this tutorial
github.com/.../custom_ble_service_example
Now I'm supposed to propagate events to the application, for example connection state...
I am using a usual uart to bluetooth application and it works great, but I would like to set this application to be a known apple midi device, it seems I only have to add...
When running ble_peripheral\ble_app_uart example..... Of course I am a little bit
corrected.....
Beacons occasionally stop.
Despite the following settings:
#define...
Hi!
Is there any example app where I can find how to use L2CAP protocol on nRF52 series? Apple introduced L2CAP in iOS 11 and I want to give it a try but I can't see any...
