Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Hi all,
I am using a C# application with the masteremulator dll to connect to a nRF51822 with S110 V8.0.0
I can bond with a new device, and communicate with it in a...
In developing the device, for very low battery consumption, I encountered a feature of the implementation Gazell (ESB) protocol.
When I send a packet from the DEVICE (PTX...
Hello,
I am a little bit confused when reading in NRF52 spec that a NVM page is 4KB while block size is 512B. Usually an NVM memory is composed of block made of pages,...
Hi,
I am testing github.com/.../nRF52-fds-example
I am on nrf52832 with sdk 12.2.0 .
I can't seem to make it work.
What i have done:
Separated FDS stuff to separate...
Hi all,
I am trying use the SAADC in blocking mode inside a RTC I am currently using
The issues comes from the example
saadc_blocking_simple
the ADC always give...
I guess this has been mentioned/asked before but you should really do something to enforce the full chip part-numbers to be listed at distributors.
For example, for an...
(Maybe this isn't an ideal place for issues with your web site, but I could see no better one.)
There is a technical non-conformance in your nordicsemi.com domain. In practice...
I've been testing my application and am having an issue opening MasterEmulator sometimes. I need to reseat the nfr51 dongle to clear out the errors I am seeing below. Any...
Hi,
I get error NRF_ERROR_INVALID_PARAM or error 0x12 from sd_ble_gap_connect in central.
I even changed peer_addr.type to 0 (BLE_GAP_ADDR_TYPE_PUBLIC).
When scanning find...
Hi, I'm trying to use an MDBT40 based board as a sniffer using the NRF sniffer firmware. I'm guessing I just need UART -> USB to talk to the chip, so I've hooked it up to...
Hi,
I am trying to figure out the best way to save power on the nrf52. I need to connect with ble about two times per day. The ble should 'woken up' by an accelerator ...
How can I flash both the dfu bootloader and an application, and have the application run after the flash?
As soon as I flash the bootloader, it kicks in doesn't fire the...
Hi,
While updating from the antique NRF51 SDK8.1.0 to the newer SDK 12.2.0, I came across a problem: Gcc crashed with:
c:\users\elm\documents\nordic\nrf5_sdk_12.2.0_f012efa...
Hi all,
i have some problem to use Timer0_IrQ.
i start first with a program that use a softdevice. After i want change this project with another that don't use it.
...
Hi,
I would like to know if the NRF51822 (Just the NRF board, not the BLE Nano) comes already prepared to be programmed or if it needs some modification. I want to program...
