Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi all,
I have a firmware in which I want to use BLE and ANT communication (with Softdevice S310) to send and receive commands from other Nordic devices or smartphones...
Hi,
I modified the code from the tutorial at devzone.nordicsemi.com/.../ to send measurements from my RHT sensor but encountered some basic difficulties. After fitting...
Hi,
I would like to know what the approximate Flash memory and RAM usage by nRF51 chipset would be when using the BLE communication (Let's say I want to send and receive...
Hi everyone
I am working with nRF52 (SD132). I am considering the ble_app_uart example and I'm trying to modify it by setting TIMER1 and TIMER2 peripherals to generate...
I'm trying to update the bootloader over the air, I succeeded to do so following the answer given here
it worked when I didn't change big things in the bootloader , but...
We have noticed that when our application is trying to call GATT disconnect while nRF master app is running, our app fails to disconnect. More over, when our app connects...
Hello everybody,
I am trying to pair module nRF51822 with Heart Rate Monitor device with the Surface Pro running on Windows 10 with no success. I see the module but when...
This question is a follow-up to this post . After performing several tests and understanding that some phone are more limited than others in terms of the number of exchanged...
Hi,
my device resets on executing sd_softdevice_enable(p_clock_lf_cfg, softdevice_fault_handler);
I have external 32KHZ crystal. I also know that software works because...
Hi all,
I have a quesion about reading a value's characteristic in the Android app nrf Master control panel.
I read a value, and i have the good value but i have a letter...
What happens if I call app_timer_start() to start a repeated timer. And at the same time I do a pstorage_clear() and pstorage_store()? Will the timer events get halted during...
I'm using the softdevice S310 on nRF51422 and when the softdevice is enable and I erase flash, the device won't go to sleep.
My code implementation is like as below:
...
There is a way to set the initial value of a characteristic. But how do I set the value after this without sending a notify to the master? Is it possible to write the value...
Hello,
i want use the port event to trigger timer 1. I need only one interrupt source and i don't want to use the pin event because of the higher current consumption. Its...
are there any cheap watch platforms that use nordic?
i want to make a kid alarm / potty alarm watch
do not want to develop hardware
would use nordic if i can find...
