Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi, I'm looking to build a simple ANT+ application. My only asset for this project is a background in C/C++. I'll need to learn/relearn the basic electronics and protocol...
Hi Nordic,
I have an application that perfectly runs in the nrf51DK but that does not work in my custom board. In my custom board everything else works (i2c, leds lighting...
I understand that in order to trigger bonding procedure you need to read/write a secure characteristic.
I am using the nRF Connect application on IPhone and trying to see...
Hi all,
I need to take samples of a period of two periodic signals and made some DSP processing with both signals.
I need at least 64 to 128 samples per signals.
I...
Greetings,
In Bluetooth 5, there is a new mode of advertisement called periodic advertisements where the advertising device can periodically advertise over the 37 non-primary...
I have a design running on nRF51 that I'm evaluating to run on nRF52. One important characteristic I'm looking for is to store it for long period with a minimum power consumption...
Having some problems upgrading the PCA10056 to firmware 1.0.1 as stated in the getting started. After downloading the only file I found I can no longer connect to it.
Can...
I've been trying to use nRF52 (PCA10040 board) with SDK 12 to read data from max30102 through I2C.
I used non-blocking read and this is twi init function and event hander...
According to S130_SDS_v2.0, I can choose to return NRF_RADIO_SIGNAL_CALLBACK_ACTION_NONE after NRF_RADIO_CALLBACK_SIGNAL_TYPE_EXTEND_SUCCEEDED to stop extend more timeslots...
I want to trigger SAADC by PPI between RTC compare event and SAADC sample task. Is it possible?
In the SAADC example (SDK 12.2.0), a timer is implemented. In function nrf_drv_timer_extended_compare...
Hi!
Which project do i need to look at in order for 5 devices which are NFR52 to send data each other
There is only one center in multilink project and other devices dont...
hello there i want to use AES in nrf51.
i want to encrypt nrf51's advertisement data . and decrypt using android app.
i have some confusions
(1) should i use nordic's...
Hi,
I'm trying out the Zephyr os for the NRF51.
When I try the basic BLE example they work fine!
However when I try the sensor example which uses the i2c it falls...
Hello Nordic Forum!
I'm currently trying to load my firmware into my custom nRF52832 board without success. I'm using the nRF52DK (PCA10040) and the nrfjprog tool.
I...
Hi All,, please confirm me this .. please confirm i-beacon Rx + ble peripheral is possible ... Also please suggest me a development kit for the same which can be easily solder...
