Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
hi,
i am using FDS to store some Data in nRF51 Development kit using temporary application. it is around 2kb. after that i am flashing main Application. is my application...
I am working on a battery-powered application. Since power saving is a must, this design using high-side power node controllers (part number MIC94042) to power-on or power...
Hi
I am looking for pin numbers for the nRF51822 microcontroller.
example like what are the pin numbers for VDD to measure battery voltage..??
I mean in which header...
Hello!
I'm learning how to use properly the saadc for knowing muy battery state of discharge. First of all I'm testing the saadc example which is included in the SDK, changing...
Hi, Nordic
I know when esb working, channel , address and pipe is very important.
From sdk and demo, I can not know these items clearly.
I know these items should be...
I need to use sd_ble_gap_adv_data_set directly and pass custom advertising data, as I need to maximise space and not send the name etc
I have been using mbed which has...
\nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I cannot find the define of pin6 pin17 pin21 pin 22 pin24
in this example ...
Hi. Can we develop and use our own firmware for any of the Nordic's beacon? Or do we need to mandatorily use firmware given by Nordic with beacon and modify them as much as...
I am using fds as my file system.
peer_manager is using file system too.
fds_register() is used to register callbacks. But how does the software know which callback is...
Hello
My nRF51 with S120 BLE stack is running as central. I want to connect 3 other nRF51 peripherals at the same time. So in the first step I did a scan and stored the...
Hi,
I'm developing an application based on the nRF52832 and I need a large throughput of over 100kbps, preferably over 200kbps.
I have managed to reach around 128kbps...
Hi
According to BT 4.2 Spec Vol 6, Part F, Section 3.2.9:-
" To write the entire value of an attribute larger than (ATT_MTU-3) octets, the prepare write request and...
hello,
i have a rather basic question concerning the design of the cycling power measurement value field.
how does a simple example for this value look like (variable...
What is the difference between SDK 8 and SDK 12 related to app_timer? I have used it like:
APP_TIMER_INIT(
APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS,
APP_TIMER_OP_QUEUE_SIZE...
Hi Nordic,
I have a star network with 3 nodes and 2 channels. I go through the whole pairing process and start sending data without problem. Now I want to, from the master...
