Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
When using the shell_module project of SDK v3.0.1, I changed uart20 to pins p2.0 and p2.2, and the serial port printed garbled text.
Below is my overlay file:
Strangely...
Beginner here .. steep learning curve for Nordic ... trying a project with I2S. Took half and hour with an ESP32, but many many hours later, no joy with Nordic.
Working...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hello everyone
I'm trying to disable advertising but it doesn't work in some cases, I don't really know why. Here is my pretty simple piece of code:
/* Disconnect and...
www.keil.com/.../uv4_db_dbg_evr.htm
www.keil.com/.../EventRecorder.html
Keil worked in a new EventRecorder feature that uses some SWD buffer memory to push data out...
Hello,
A question to understand please. A lot of issues still unfixed in rev 1, but are known for a long time (see errata docs). Like SPI with RX = 1, DCDC -4dB on RF,...
Hello, I try to run the sdk example for adc, i set an input voltage in varying from 0 to 4.38 V in the pin 4 (AIN2), but the returned value didn't corresponds to the desired...
It there a specification for current draw during POR? (From time Vdd starts rising until cpu starts executing?) For nRF51 and 52.
I found this devzone.nordicsemi.com/....
(Hello! I'm drawing the module circuit base on nrf52832 with rfx2401 power amplifier (PA). As I understand it needs to set pins TXEN, RXEN to high level to activate this PA...
It may sound a bit old and you may have fixed them in latest Soft Device stacks however I wanted to share with you a couple of pairing issues we encountered with Soft Device...
i am using nrf52832 and programmed it with eclipse by blinky example.. now i have to debug the project , but when i debug the project with the configuration given in tutorial...
Hi,
We are using a BL652 from Laird, embedding a nRF52832. We wanted to give Zephyr a try, but we are facing a problem.
We compiled the blink example, but when we flash...
Hello dear Nordic members,
I got a theoretical question: I want to connect two chips, one as central and the other as peripheral. Is it possible to stop advertising procedures...
I am using nrf51822 for a BLE project as peripheral role. I am using S110 soft device (SDK version 10).
I want to store bonding information, GATT data and all data storage...
Hi ,
I am working interfacing SD card with nrf52 using fatfs example given in SDK 12.0.0. While writing to text file created in root directory, code gets stopped as size...
Hi - I am designing some boards using the NRF52832 and would like to check a couple of things about footprint design. Unfortunately I don't have access to Altium, and am therefore...
Hello,
I did a code that does scatternets with nRF52 (in connected mode) but it's very dirty because i collected informations all over forum during months and project was...
Dear Nordic Support Team,
In a recent news received by email regarding a new version of "nRF5x Command line tools v9.2.1", it is written that Nordic does not recommend...
