Hello,
I am using the same hardware, and firmware on 4 custom boards of the same device. I observed that I am getting different current consumptions in each devices.
I...
I’m working with a device that communicates over single-wire UART (half-duplex), where TX and RX share the same line (because the peer device is designed that way). Now I...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
If an app is advertising on all channels, and receives a SCAN_REQ on 37, will it transmit the ADV_IND (and potentially SCAN_RSP) on 38 and 39, or is advertising interrupted...
I am attempting to use sscanf() on nRF51822. However the chip simply freezes when reaching that part of the code. Do I need to add anything in the toolchain to make it work...
I'm using nrf51, I noticed that when I disable some functions calling (in the file flash_memory_management.c ), the behavior or the function in the file ( fatigue.c ) is correct...
Hello ,
Easy question, I am using the nRF52832 and am trying to find out if all gpio pins have gpiote functionality? And if so can all gpios be configured as an external...
hi
this is my timers_init(); func
static void timers_init(void)
{
uint32_t err_code;
// Initialize timer module.
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS...
I am writing an App for the Central/Master side using the s130 v1.0.0 SD. I am connecting to the soft device using the python wrappers for the nRF51-BLE-Driver-Win 0.5.0....
I want to write a program in Keil by SPP for communicating with a thermal printer that uses SPP
but I can't find source code about that.
Is this possible to do this with...
Hello
i have nrf52 PAC10036 dev Board.
i am using the visualgdb.
when i try to create the instance of the TWI.
i got the error
please check image for detail.
How i can...
I want to turn off BLE-peripheral Advertising for 8 hours but I want to use another timer with period of 50ms to scan GPIO ,
when I change prescale of
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Hello,
is there a good documenation or introduction about the Programmable Peripheral Interconnect Feature? I read the short part in the Objective Product Specification...
Hi everyone,
I need to use an nRF51822 (MBH7BLZ07-109033) mounted on a custom board.
I want to develop my firmware application on the custom board in such a way I can...
Hello,
I am using nrf51822 doing projects. I met an issuse which is that at the first 6 minutes, it can normaly go into UART interrupt and run subroutine successfully....
I'm testing out TWI on pins 24/25 and I get a crash when I attempt to do a TWI transfer and I find myself in: WDT_IRQHandler ()
I'm using much of the example code:
APP_TWI_INIT...
Hello, I have a few nRF devices, and I am unsure as to which revision the ICs are. Here are the three HWIDs:
0x00AE,
0x0086, and
0x0077
I tried looking into the nRF51_Series_Compatibility_Matrix_v2...
Hi,
I need to sample 2 inputs at 200Hz and send it on an app. Can I send the data at this speed using UART service? I was trying to do it using HRM example but could not...
