Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
Hello,
This is the first time i use NRF8001 chip, i was reading the ic manual nrf8001_PS_v1.1.pdf (see attached file).
It was written that in case i used DC/DC converter...
Hello,
I checked Nordic website for layout of NRF8001 but i didn't find.
Please if some one can share a qualified RF-layout.
Help is appreciated.
Regards,
Hisham
from training document from Nordic company(see the attachments),it mentioned that we can add scan response .but i can not find any information in BLE_HRS demo.could you tell...
Hello,
I made a PWM with the TIMER2 of my nRF51822 (with the SoftDevice) and was working fine, till I read that I should not use the "NRF_PPI" functions and use the "sd_ppi_XXX...
I've got an nRF51822 development kit that I'm trying to get started on. I've gone to Kiel and downloaded uVision 4 (mdk472_a). I install it with all default settings and it...
Hi,
I add UART support using IRQ on the "ant_hrm_tx" example code.
and I'm sending packet of 4 bytes that contains: Delimiter,HeartRate,Battery,Delimiter
the frame...
Hi, I am trying to test my UART using some simple loopback test, and I have noticed that the service discovery command of BLE will occupy the CPU a quite long time. I am just...
I was unaware that the 'manufacturer data' in the advertising packets is limited to less than a full payload. However, whenever I set it to >6 the program "crashes".
...
When I use keil to download the software to the chip, there are two questions:
like attached.
2.NRFGO CAN'T SEE J-LINK LITE CORTEXM BOARD
Is there any way to solve...
We have recently moved to a new PCB which puts the nRF8001 on the layout instead of plugging into a nRF2741 development module. The nRF8001 connects to a TI Cortex-M4 Tiva...
Hi, we would like to create a kind of game using 2.4Ghz emitters . The 2.4Ghz USB Dongle emits and the mobile phone detects the frequency + embed unique ID/code so we confirm...
To be more detailed:
One of my ADC pins will be connected to another device that could be providing a voltage of about 3V, but through a 100 kohm resistor. (actually it...
Dear Nordic Developer Zone,
Since I have implemented a timer with interrupt in my application, the debug mode if the Keil IDE stops working when I try to restart the code...