Hi,
I have a custom board build with an nrf9151. Right now I'd like to have the possibilty ti get modem trace. But it's look like I got crypted/corrupted data from UART1...
Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
Dear all,
i building the example light_switch_server_nrf52832_xxAA_S132_7.2.0 from solution l ight_switch_server_nrf52832_xxAA_S132_7.2.0 in configuration Debug (SDK nRF5...
Performance on hardware (cc3xx) is significantly slower than performance on software (oberon). Does anyone have a good explanation for this? I have also tested ECDSA and can...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
I have a custom hardware running on nrf52840 and using ncs 2.6.1. I have implemented a custom authentication flow with customer characteristic along with the BLE bonding....
Hi,
After I've successfully connected my smartphone via nRF Toolbox's UART-BLE Service to my nRF52 peripheral, I tried to mimic the scenario when the devices get disconnected...
Hello
I want to understand how far the firmware that is burnt on to a Hardware is protected. Is it possible to actually read the firmware from a device (if the device has...
Services Setup
I am trying to feed the "Services Data" manually to the nRF8001.
As per the data sheet page 82 (see image below): Upon transmission of 1 packet of data...
I am trying to run the ble_app_beacon example on an nrf51802 device.
The call to sd_softdevice_enable() never returns (jumps to 0xFFFFFFF9)
The fault handler is not called...
My guess is that:
Characteristics are (or at least, can be considered) subsets of services, which in turn, are (or at least, can be considered) subsets of profiles.
...
Hi, I am modify the S120 multi-link UART example code (code is available here ), and just noticed a problem that the central is only able to send the UART data to the last...
I have tried to make IAR working on monitor mode.(Follow this devzone.nordicsemi.com/.../ . )...up to today the NRF52 still will reset once I hit breakpoint on power_manage...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
Hi, we are updating our current application to the new nRF5 SDK and S132 v2 softdevice but we got stuck with a issue on the initialization of a custom service.
We narrowed...
I'm a beginner at Homekit development.
And I'm using HK SDK3.0.1 on SDK12 for Homekit as Accessory.
At the first,
How to change advertising data, such as Device ID and...
I have a question about Nordic's implementation of FreeRTOS. In the FreeRTOSConfig.h the following is defined as:
/* The highest interrupt priority that can be used by...
I have a star network that works faithfully in no ACK way, using only pipe0.
Now i want to use pipe 1 to transmit from one nRF24L01+ to the star center, with ACK this time...
Hi All,
I would need to get around 11Mbps data rate. I need around 5meters range. Is it possible to use multiple antennas and do a sort of MIMO.
Thanks,
Paul
Hi,
i am disabling ppi channel so that my adc should stop working(i am taking data from 3-axis accelerometer), this process i am doing by pressing button(bsp_event_handler...
