Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
The v3 reference manual of the nrf51 mentions:
"[The powerfail comparator] also provides hardware protection of data stored in program memory by preventing write instructions...
If I use the interrupt handler to set Flag, and read sensors and write data to SD card in the main loop as in the following code then everything works well.
#include <Wire...
What hidden settings am I missing this time in the awful Segger studio ?
I get an error :
unknown type name class
When I compile with this new class called...
hello i am new to spi, i am doing project on 3 wire spi interface. I am using 3 wire interface as Sclk,ssn,MOSI pins only , I am not using MISO pin .I am tested spi example...
hello, I am working on nRF52 DK spi protocal.I am using AD9837 as slave.Here i am using 3 wire interfacing.I am connecting Sclk,ssn,MOSI pins olny & I am not connecting MISo...
what's the maximum data rate of nrf24l01+ (with ACK and without ACK) using 2 nrfs?
if i use 4 nrf24l01 two in tx side and two in rx side.what would be the maximum data...
Reading the migration doc at:
<SDK>/components/softdevice/s130/doc/s13x_nrf5x_2.0.0_migration_document.pdf
I see there's a new fault handler type and an implementation...
Hello all,
I need to program nRF52 via the SWD pins. I cannot use the nrfjprog or J-link or Segger etc. I have connected 3 wires to the nRF52 - SWCLK, SWDIO and GND.
...
Hello to all
I'm working in an application that needs to be completely power optimized. In this program the device works as a scanner that if it finds an specific device...
Hi, I am wondering about the pre-made PCB's available on ebay, with a nRF24L01+. At a cost of $1, and with various forum stories over the Internet referencing issues such...
I am using NRF51422 S130. I have a master SPI configuration set up, and not using Nordic spi drivers provided in the examples. I think my configuration is correct.
1- I...
Hi,
We started out developing an application using the SoftDevice 1.0.0-3 (from SDK 0.9.2). We now need to upgrade to SoftDevice 4.0.2 (included in SDK 13.0.0).
We already...
Hello, I have some ideas to do for IoT and bluetooth. Already did some tests with MQTT raspberry pi and ESPs SoCs. Then I started to dive into bluetooth world and I found...
Hello,
I'm working with SDK 11 on nRF52832.
I want to get the IRK from a connection event. I need to identify the connected device.
My following code :
static...
