hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hello,
I bought few nRF24L01+ modules and I integrated them in some custom PCBs that I designed.
I haven't been able to transmit information:
The TX FIFO is full...
I'm working on a very simple Gazell build - basically the gzll_ack_payload example with some of it pulled out, since I'm working on a board with no LEDs or buttons to run...
Hi,
I am trying to develop a PCB for the NRF52 that will use bluetooth capability. However, I was wondering if there were smaller antenna's that could be used rather than...
If I have Bluetooth earbuds, one set to master and the other a slave on my ears.
Is the communication between the ears, through the head, or around the head (Hair scalp...
Hi all
I have two questions/problems regarding the emulated System OFF mode with the NRF52832 and the SoftDevice S132 V2.0.1:
According to this thread , an infinite...
It is to my understanding that you DO have to worry about that when using keil download function or other means to program either the softdevice or your program to the nrf514xx...
hi,
I have created shared channel. currently I only have one master and one slave working.
Master is sending data to slave and it s working perfectly.
But I can not...
Hello,
i haven't found an answer to this question. Which address uses the PTX in Enhanced Shock Burst Protocol (nrf52832, SDK 11)? In the code I found only that:
NRF_RADIO...
Hi
According to the BT spec v4.2, Volume 6, section 4.5:-
"There shall be only one connection between two LE device addresses.
An initiator shall not send a connection...
As show in the title, suppose I have my own bluetooth stack implementation, Is there any possible to flash the bluetooth stack into the nordic series?
Or, another question...
Hello
I'm able to use the MasterEmulator in a WPF or command line application but when I try to use it in Windows PowerShell i get an error.
I'm trying (with the dll...
Hello,
We've been struggling for a while trying to understand how to interpret the nRF52832 electrical specification . Sorry if this may sound like a bad question but we...
Hi, I'm using SDK12 and I'm trying to implement button debouncing. I have initialized one of the nRF52 board buttons using app_buttons.c. In the infocenter I read that debouncing...
Hi!,
I have load Sniffer_firmware into PCA10028 and works, but I can load Sniffer_firmware into PCA10040? it's compatible?
This file --> ble-sniffer_nRF51822_1.0.1_1111_Sniffer...
Hi,
I have tested mbed Classic and mbed OS with CLI and Yotta and works with nRF51-DK and nRF52-DK. Also with Eclipse Neon.1 with yotta build Eclipse CDT4 - Ninja.
But...
