Hi Nordic
I’m working with the nRF5340 and nRF21540 for 802.15.4 and would like to know:
The expected RX sensitivity estimation for this combination.
Any reference...
Hi, How do we send a byte array using mosh? From the documentation I can see: sock send -i 0 -l 100000 This specifies the socket and the length. But how is the actual data...
Dear Nordic Semiconductor Team and Community Members,
I am currently working on an nRF54L05 project where I aim to use only the primary slot in MCUboot due to memory constraints...
Hello team,
We are using nrf54l15 platform using NCS 3.02 SDK.
When advertising the MAC address changes in two following conditions
1. After every reset
2. After connect...
Is there any documentation around the process to disable the Debug Access Port on a nRF54L device in software (not nrfutil)?
The nRF52840 has this nice documentation page...
Im trying to use the https://github.com/apache/mynewt-mcumgr-cli project to update my rfF54L15 with a DFU package
Setup: Raspberry PI 4 and and nrF52840 USB Dongle
I...
Hello everyone,
I have a program which set configurations by using write (nrf_drv_twi_tx) in the registers of a sensor.
I use the SDK 8 in the nRF51.
Here is the code...
Hello, I want to test using RTT for logging since I am using UART for send/receive packets. I made following changes in sdk_config.h:
#ifndef NRF_LOG_ENABLED
#define NRF_LOG_ENABLED...
I have device with nrf5x and I will customize this device on production. I use to flashing nrfjprog.
Will prepare one hex file and customize e.g serial number during flashing...
Good time dear Engineers!
Faced with a general Problem.
I use two nRF52 boards connection : Central <-> Peritheral.
init data: MIN/MAX conn intervals = 10/30 ms
...
I noticed that the GPIO port read and port write for SDK v12.2 changed to accommodate chips with more pins but I can't find much information about it. How do I use nrf_gpio_port_out_read...
I want to make a frequency of 750khz, 50:50 duty ratio.
How do I use pwm?
I use it. nRF52832 PCA10040
I used the PWM library example but it failed.
The frequency...
I'm using nRF5SDK V.12.2.0.
In the app_ble_uart example, trying to change MTU size as below.
#define NRF_BLE_MAX_MTU_SIZE 103
...
#if (NRF_SD_BLE_API_VERSION == 3)
...
I am using SAADC with TIMER3 and PPI, sampling 12bits at 250Hz.
When I use 10uS acquisition time, the average current consumption is 300uA lower than when using 3uS or 5uS...
With nrf Toolbox 2.2.1 on android 6.0.1 (Google Nexus 7 or OnePlus 3T), I try to transfer an application firmware in a zip file UiBoardV0.4.1.zip , generated with "nrfutil...
Hi,
In am using a nrf52832 in a serializated configuration, with the softdevice S132 on the connectivity board.
Is there a way to configure GPIO on the connectivity...
hello,
i have one nrf51 dk and it has some advertisement packet, i have another nrf51, i want this another nrf51 to copy first nrf51's data. can you tell me how to copy...
I stumbeled across a problem with my application, which runs on s120. My case is: I have a S120, configured as a peripheral and I have an Android 5.0 Motorola smartphone....
Hi, I'm trying to install the BLE buttonless DFU template onto a nRF52 (PCA10040) eval board using the secure bootloader example (with s132, version 12.2 of the SDK) via nRF...
We have a new project it is as preipheral. It will support dual bank OTA. We want to use the IC of nRF52832 and use SDK12.2. I want to know which softdevice and bootloader...
I bought new nRF52-DK. I am am trying to connect it to windows 10 system over usb 2.0 mini port. I have installed nRFgo studio and JLink drivers. The problem is nRF52-DK is...
