Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello,
I'm looking for details on the nrf52 DAP signals SWDIO and SWDCLK. Such parameters als min. time high, low to Z, clock duty, maximum frequency, minimum frequency etc...
I am working in a custom board which is having nrf1822 chip and I am using Softdevice s130 2.0.1 , SDK 11.0.0, RAM available is 16Kb where soft device uses 5kb of RAM,heap...
I am duty-cycling the radio, so I listen with a timeout and then power off the radio (or transmit) if no packets were received. Currently I am ignoring the address event from...
Hi,
I have programmed s212 soft device onto to NRF52 DK and also programmed ant_broadcast\tx application onto the NRF52 DK. The LED is glowing to indicate that TX is happening...
What is the maximum input voltage for the ADC on the NRF52. I found answer for the NRF51 but nothing definitive on the NRF52.
I have a photocell (or LDR) to sense light ...
Hello,
I am trying to make a basic uart communication between my nordic NRF52 dev board (PCA10040, s132) and my STM32f429ZIT6 discovery board.
NRF52 : I used the example...
Dear Sir,
I and new of development nRF51(256K/16K), I read some sdk docs, but need further information and help.
Would like to save some application information...
Hi,
I'm trying to use the same timeout_handler for two different timers. I use the p_context (as explained here ) to pass a flag to the timeout handler, so that he knows...
At the start of programm, I create a timer_id used the follow code:
app_timer_create(&m_sec_req_timer_id,APP_TIMER_MODE_SINGLE_SHOT,sec_req_timeout_handler);
when the...
Hi, I started using the nRF51422 kit today. Downloaded nRFgo Studio, Master Control Panel, nRF Connect, BLE Sniffer, Wireshark 1.10 (after figuring out that you don't support...
Hai
i am planning to make an iot project with ble for my academics. I am using arduino to control the ble.
I was done a test with blend micro to know its maximum range...
Hello I would like to use more dongles with pc-ble-driver-py. For example I want to create multiple advertisers and test that my DUT would see multiple advertisers. I tried...
Hi all,
I was looking into using a PWM for LED dimming, and in an attempt to smooth out transitions between light states, I found that there was visible flicker as the...
Hi
I want to ask what the this define
#define NRF_CLOCK_LFCLKSRC {.source = NRF_CLOCK_LF_SRC_XTAL, \
.rc_ctiv = 0, \
.rc_temp_ctiv = 0, \
.xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_20_PPM...
Our code is 21k excluding soft-device,as per the example 15k should be the max size limit of code to update FOTA. Is it possible to make changes in DFU bootloader so that...
