I have a project that I need to use most of the GPIO pins available on the nRF52840 DK. I'm using SDK V17.
I'm writing a test program that toggles all GPIO pins on an nRF52840...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi,
I am developing a glucose application using nrf51822 chip.
Now i want to go for mass manufacturing.
All my devices are advertising the same name.
I want to identify...
Hi all,
I was testing with a new nRF51 Dongle recently and am finding that it disconnected from any peripheral after 15-18 seconds. Generally a little while after a Connection...
I had a PWM question ( here ). It was recommended that I install SDK 10 and use the PWM files from SDK 10. I installed and copied the PWM files from 10 to 9 and opened my...
Hi, I've compiled program from this link:
developer.mbed.org/.../
The problem is that I can't connect to my DK by nRF UART 2.0 app, probably because not every UUID is...
I am working on adding a timer in the ble_app_uart sample, aiming on disconnect with device which doesn't send any data in specific time, such as 5 seconds.
Now I have...
I get NRF_ERROR_SVC_HANDLER_MISSING error in spi_open function.
uint32_t err = sd_nvic_ClearPendingIRQ(p_spi_instance->irq_type);
APP_ERROR_CHECK(err);
I'm using...
hi,
I need to store persistent data of about 32 bytes in flash, so tried using pstorage APIs (SDK v9.0 on nRF51822 -- 256KB ).
I followed the sample code given here...
Hello,
I am using keil uvision 5.17, sdk 9.0.0 and sd 130.
Once I programmed whole application through mbed,
Then I moved into keil and implemented all function....
We are trying to communicate to NRF51422 through PC using UART communication. But the programs works fine with nRF51822 Dongle and DK. But it does not works with another dongle...
Hi experts,
I need nrf51822 to send thousands of packets (notification) to Master Control Panel (PC), and expect for high data rate. So, I turned the connection interval...
if initial uart_config() before ble_stack_init(), softdevice_handler_init will be failed!
with SDK 6.0
softdevice_handler_init() will returns 0x00001001 ("NRF_ERROR_SDM_INCORRECT_INTERRUPT_CONFIGURATION...
I am trying to generate code using BDS and the Nordic Plugin 1.2 but I keep getting the following error. I have reviewed the XML but I can't seem to find the issue. Any thoughts...
I've been fighting this bug for a few days now and I thought I'd share what I discovered in the process.
I wanted to set up a couple PWM channels to control a few LEDs...
getting problem in implementing uart. code is here
#include <stdio.h>
#include "boards.h"
#include "app_util_platform.h"
#include "app_uart.h"
#include "app_error.h...
